The PSA is referring to Kconfig symbols that are only found
in Nordic downstream repo so we cannot use it anyway atm.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This avoid compliance warning
Found pointless 'menuconfig' symbols without children. Use regular 'config'
symbols instead. See
https://docs.zephyrproject.org/latest/build/kconfig/tips.html#menuconfig-symbols.
WIFI_NM_WPA_SUPPLICANT modules/hostap/Kconfig:8
WIFI_NM_WPA_SUPPLICANT modules/hostap/Kconfig:8
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The big cherry-picking left some invalid code so remove/fix
it in order to pass the compilation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a typo, channel and frequency were compared causing the
connection to fail for any combination.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Use the WPA cli command to disconnect a station in AP mode.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The WPA version was only been set for WPA-PSK and WPA2-PSK, but for
others it wasn't set. For AP mode this causes issues as WPA-IE is
considered and WPA3/WPA2-PSK-256 aren't allowed, they need RSN.
Explicitly set the version for all to RSN, except for WPA-PSK.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For AP we should use the security mode from the SSID as stations can
have a different security than the configure one. E.g., WPA/WPA2 in AP
vs WPA in STA1 and WPA2 in STA2.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If the interface is in associated state, then current SSID will always
be set, so, add an early check and use SSID info freely after that.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This way we reject disconnect in AP mode and ap disable in STA mode,
though both have same functionality we treat them differently to keep
it clean.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These are to intimate the applications about connected Stations.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These events are used by AP mode, tied to AP-ENABLED and AP-DISABLED
events in the hostapd/wpa_supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These can be abstracted from the core WPA supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The management frame structure in the WPA supplicant only has a pointer,
so, it need a deep-copy before passing it to WPA supplicant, else driver
ends up freeing causing invalid memory contents.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI should only be retrieved for STA mode, but the check was wrong.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The keyword is added into array argv of wpa_cli.
The commands which require to be interactive
this keyword will allow ro print output for them.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Before starting AP mode, we don't need to search for existing networks
and join them, as the use-case is starting SoftAP.
This speeds up the AP mode operation significantly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI is only applicable for STA mode, as for AP there are multiple
peers. This causes failure and unnecessary delay, so just skip the
retrieval.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user enables AP mode, make sure CONFIG_AP symbol
is enabled so that access point sources get compiled etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA supplicant handle is not used anymore.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This prepares for the upcoming AP mode support and moves re-usable code
to a common helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These were missed in the original support.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of assuming that the array is perfectly aligned with enum, moved
to a data driven design, this decouples from the enum numbering and also
helps avoid repetition of the event string while parsing.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This is a implementation gap and shouldn't be exposed to customers.
But when we run with debug it still helps to identify any important
events that are not handled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Using "%02x" needs an unsigned integer, but all MAC addresses use
"unsigned char/char" as the data type, so, to avoid warnings, use a
temporary array.
Also, the macro from the WPA supplicant doesn't use the address of the
array element and causes warnings, so re-define the macro with address
of the element.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the WPA supplicant internal event has a MAC address, and the sample
is compiled with newlib-nano then then the parsing fails because of lack
of support for C99 formatting options in nano [1].
Fix this by using supported specifier, even the code that encodes the
message uses the same format specifier.
[1] - https://docs.zephyrproject.org/latest/develop/languages/c/newlib.html#formatted-output
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enabling a network would trigger a scan. Since frequency is being
set after enable_network, first scan is issued without any
specific frequency.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA-PSK was added a bit late, so, it wasn't properly implemented, use
both key management and protocol version to properly handle WPA-PSK in
both connection and also in the status.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
MBO and WMM-AC are mandatory for WFA certification, so cannot be
disabled for memory saving.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
wpa_supplicant has a lot of entries, and it appears in the top-level menu.
Let it be a menuconfig, so that it gets its own menu page with
all the options, instead of expanding in the top-level menu when
selected.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a user provides both band and channel then check if they are
compatible or not.
Also, move the multiple remove network cleanup to goto.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
By default Wi-Fi works on all bands, so, the band will be unknown, in
which case no need to configure a specific frequency list to WPA
supplicant.
Only when a use provides a specific band then this is needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This allows the WPA supplicant to build using the builtin MbedTLS.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a specific band is configured, automatically fetch and configure the
supported channels.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For a memory constrained system, basic Wi-Fi is enough, so, add a
configuration option to compiled out advanced Wi-Fi features.
This also supports choosing individual features if needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This should solve latency issues with using system workqueue and can now
closely implement the configured timeout.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The macro for crypto has been renamed (and as a choice), so, use the
new macro to see if the crypto has been enabled.
Fixes WPA2/WPA3 association.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This hardly saves flash but helps us in doing PSA port stagewise,
personal first and then enterprise.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a bug in Kconfig, both legacy and PSA crypto were enabled
earlier, so, the dependencies for PSA were missed as they were provided
by legacy.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This set of changes introduces an API to set the channel when
the device is working in independent Monitor or TX injection mode
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This set of changes brings in packet filter API for Monitor and
promiscuous mode operation
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This change provides mode setting API to hostap module.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The control interface is initialized on every interface add but only
de-initialized on WPA supplicant termination. This leaks all cleanups in
the control interface dei-init.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enable the PSA key type which enables AES block cipher support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Jukka Rissanen