The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix the qmsi i2c driver and the relevant SoCs accordingly.
Also applying relevant changes on quark_se_c1000_ss as it can use i2c
qmsi driver as well along with qmsi ss i2c driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that all arch using QMSI gpio driver are generating the right
settings through DTS, these options can be removed from Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name and irq flags generated through dts as well.
Fix Kconfig for the gpio driver accordingly.
Irq priority is not set by dts for D2000 as it's irq controller does
not support it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
patch removes Kconfig defines for RAM and ROM size in x86. Instead
these values are derived from dts.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Selecting a choice symbol is always a no-op, and the latest version of
Kconfiglib prints a warning. This commit removes all selects of choice
symbols, which might make the Kconfig files a bit clearer and gets rid
of the warnings.
This is just a dumb removal. I did not try to guess the intent of each
select.
Fixes#6849
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Applying the change to relevant arch/boards, either in their Kconfig or
the dts specific files.
Taking the opportunity in dw driver to rename the variable the same way
as they are everywhere else in the code (s/dev/dw and s/port/dev) in
init function.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move common SoC dts.fixup defines into arch/x86/soc/atom/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/ia32/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/x86/soc/intel_quark/quark_se/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A fix for this issue is in progress, meanwhile warn the user that
they may be susceptible to this problem if they enable user mode on
an x86-based target that is not known to be immune.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When CONFIG_X86_MMU is enabled for arduino 101 the start address
should be aligned to 4kB. If not aligned the page tables would not
be created and the build fails.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Configuring the RAM/ROM regions will be the same for all
x86 targets as this is done with linker symbols.
Peripheral configuration left at the SOC level.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
'commit
("devicetree: Generate BLUETOOTH_UART ,UART_PIPE etc config from dt")'
created a dependency of selecting UART_QMSI_0 on device tree.
This change is reverted as it incorrect.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch uses chosen property zephyr,bt-uart, zephyr,uart-pipe
and zephyr,bt-mon-uart to determine the uart instance to be
used for bluetooth,uart_pipe and bluetooth_monitor and generate
appropriate configs.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Sebastian Bøe