Esp-idf defines the BIT macro that is also defined in Zephyr's
misc/util.h. Fix the issue by including the esp-idf headers first, so
that a check in util.h won't redefine the macro if it's already
defined.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
- .text, .text.*, .literal, .literal.* had no matching input section
rule and were being passed to the output binary verbatim. These
are all now in the output "text" section as intended.
- various rules in the data section were unnecessarily using KEEP().
- SW_ISR_TABLE wasn't included in linker script anywhere and was
ending up in its own section, and not the data section as intended.
- noinit section didn't exist at all, now defined.
Issue: ZEP-2508
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This cleans up the exception handling by removing the table declaration
from xtensa_intr_asm.S, and removing the unused
_xt_set_exception_handler() function.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The Xtensa port was the only one remaining to be converted to the new
way of connecting interrupts in Zephyr. Some things are still
unconverted, mainly the exception table, and this will be performed
another time.
Of note: _irq_priority_set() isn't called on _ARCH_IRQ_CONNECT(), since
IRQs can't change priority on Xtensa: while the architecture has the
concept of interrupt priority levels, each line has a fixed level and
can't be changed.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The first stage bootloader, part of the ESP32 ROM, already sets up
a stack that's sufficient to execute C programs. So, instead of
implementing __stack() in assembly, do it in C to simplify things
slightly.
This ESP32-specific initialization will perform the following:
- Disable the watchdog timer that's enabled by the bootloader
- Move exception handlers to IRAM
- Disable normal interrupts
- Disable the second CPU
- Zero out the BSS segment
Things that might be performed in the future include setting up the
CPU frequency, memory protection regions, and enabling the flash
cache.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Due to the configurable nature of the Xtensa platform, the generic name of
"LX6" cannot be used to describe an SoC as far as Zephyr goes. So ESP32 is
defined both as a SoC and as a board.
This is based on work by Rajavardhan Gundi.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Use TOOLCHAIN_VARIANT to indicate what XCC toolchain release
to use.
Set a reasonable default for the RG-2016.4 toolchain release.
D_108mini, D_212GP, D_233L are only in RF-2016.4, set that
appropriately.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add QEMU_CPU_TYPE for the sample_controller, so that zephyr image could
be run on QEMU with sample_controller core.
Change-Id: Id9e97a43c4b7921142289dcf97ff782993ca0463
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This SoC, in its default configuration, does not have any SW IRQ below
the EXCM level. This make it unsuitable to use irq_offload() and thus
almost untestable.
Decision was made to remove this configuration in favorof custom one
XRC_D2PM_5swIrq, which is the same core but with additional 4 SW IRQs
of level 1 and an additional timer.
Issue: ZEP-2029
Change-Id: Iee4f8346aa9d610e14898444f78d28ef0ac4cef2
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Move linker/common-rom.ld between .rodata sections so that it's together
with other immutable data.
Move linker/common-ram.ld before the .bss section, so that .bss does not
appear between data sections, which had two consequences:
- there's a .bss-sized gap in the ELF image, and
- PHDR segment that covers .bss overlaps the segment that covers .data,
resulting in the following xt-run warning:
( [ sample_controller ] load_bfd ) *WARNING* Executable segment
[ 60004d60, 600079a7 ] overlaps an existing executable segment
Change-Id: I2db46f4656e240016fe60883057cc000b6377180
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* CONFIG_SOC is now properly set and we do not need a separate
XTENSA_CORE build variable
* Some unnecessary macro -D CFLAGS in the Xtensa Makefile removed
* There is no default SOC selection, it is now done explicitly in
the board's defconfig
* CONFIG_<board name> now renamed to CONFIG_SOC_<board name in
uppercase> to conform to established style.
Issue: ZEP-1711
Change-Id: I88997530db09970b7fdd1c3e3d355bfca9d0be1a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This core is not depreciated and compilationfor it is even faster than D_233L.
Change-Id: I6b8149ca9e879770c3ed0973ffb9304e2e3c8d8d
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This was introduced during a copy/paste when updating patch
https://gerrit.zephyrproject.org/r/#/c/10323/6..7
Change-Id: Id6857dd28a16974361932285b44559f702c4d910
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Master branch changed requirements for license headers while this
branch has been in development.
Change-Id: I9bce16ff275057a4bb664019628fc9b6de7aef7c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Provide generic support for running zephyr kernels on xtensa QEMU and
map D_233L SoC to dc233c QEMU core.
Change-Id: Ie804588f750213a7cc54dbc95c86ee4d62ba1ea5
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Added arch sub folder, make files and Kconfig files for a set of standard SoCs.
Change-Id: I4ee9cba966860072e55c95795d87356b665e4d49
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Leandro Pereira