Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The lowest level of the x86_64 bit port supports the full 64 bit ABI
just fine, but Zephyr does not (yet) and builds under the x32 ABI
instead. The xuk layer can be built with or without the -mx32 switch,
and it had a configurable in a header to tell it what it was. At some
point during development I swept through and turned all those tunables
into kconfigs, but this one wasn't used by zephyr and so it got the
CONFIG_* rename but never had an entry added to a Kconfig file to
match it, and eventually got picked up by Ulf's unused symbol
detector.
Rename back. It will probably become a kconfig again someday when we
need it. Fixes#14059.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Some more were added since the cleanup pass in June 2018. See e.g.
commit 2d50da70a1 ("drivers: ipm: Kconfig: Remove redundant 'default n'
properties") for a motivation. It also avoids people wondering whether
or not they need to put in 'default n'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There is an effort underway to make most of the Zephyr build script's
reentrant. Meaning, the build scripts can be executed multiple times
during the same CMake invocation.
Reentrancy enables several use-cases, the motivating one is the
ability to build several Zephyr executables, or images, for instance a
bootloader and an application.
For build scripts to be reentrant they cannot be directly referencing
global variables, like target names, but must instead reference
variables, which can vary from entry to entry.
Therefore, in this patch, we replace global targets with variables.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Patrik Flykt