The Kconfig symbols for RX/TX LSB first didn't match between the driver
and the Kconfig file. Change driver to match Kconfig symbol names
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The generated defines RTC_0_CLOCK_FREQUENCY and RTC_0_PRESCALER are
maked as deprecated by dts generation. This causes a build warning and
an error during sanitycheck runs. Replace with the DT_ prefixed
versions that are not deprecated.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit 040d6b6e99 (eth: eth_mcux: Convert to use DT_ prefixed defines)
changed all the defines, but to incorrect ones.
This commit changes them to what actually gets generated.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The hwinfo shell uses shell functions and thus doesn't build when
CONFIG_SHELL=n. Fix that by adding a dependency on SHELL.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
DT_USB_NUM_BIDIR_ENDPOINTS includes EP0, which we should not
take it into account when we check endpoint capabilities
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Convert generic FLASH_{WRITE,ERASE}_BLOCK_SIZE to driver specific
generated define DT_JEDEC_SPI_NOR_0_{WRITE,ERASE}_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert generic FLASH_WRITE_BLOCK_SIZE to driver specific generated
define DT_SOC_NV_FLASH_0_WRITE_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert generic FLASH_{WRITE,ERASE}_BLOCK_SIZE to driver specific
generated define DT_SOC_NV_FLASH_0_{WRITE,ERASE}_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert generic FLASH_ERASE_BLOCK_SIZE to driver specific generated
define DT_SOC_NV_FLASH_0_ERASE_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert generic FLASH_WRITE_BLOCK_SIZE to driver specific generated
define DT_SOC_NV_FLASH_0_WRITE_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On behalf of : Timo Teräs <timo.teras@iki.fi>
UART_REG_ADDR_INTERVAL is SOC / chip implementation specific feature,
and its width does not always correspond to current settings for
IOPORT/non IOPORT access method.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The eth mcux driver has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The i2c_imx driver has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The gpio mcux driver has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support to STM LIS2DW12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Co-authored-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The values for the registers like GDV, SDV and Boarder Waveform
depend on the panel and display controller. Add DT properties
and obtain such values from DT.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Replace generating CONFIG_ symbols with DT_ symbols for chosen
properties like 'zephyr,console' or 'zephyr,bt-mon-uart'. We now use a
kconfigfunctions (dt_str_val) to extract the info from dts into Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for socket CAN functionality. This means that user
is able to use BSD socket interface to send and receive CAN
packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instance 2 & 3 for some reason never transitioned CONFIG_SPI_*_IRQ_* to
DT prefix. Fix that since those Kconfig symbols will never exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The PWM driver can only control channels 1-3 of the PWM peripheral, not
channel 0. This is an artifact of the peripheral's design.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
This patch adds basic support for the PWM devices available on the Atmel
SAM family. Beside enabling the driver, everything is selected through
the device tree, including enabling the PWM0 and PWM1 devices. Thus
CONFIG_PWM_0 and CONFIG_PWM_1 are ignored.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SAM GMAC Ethernet driver currently keeps a reference to the packet
being sent in addition than keeping of references of the fragments. In
practice this is only needed when PTP is enabled, otherwise the driver
only need to prevent the fragment (or even their content) to be changed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SAM GMAC Ethernet driver uses scatter gather DMA to transmit data.
Each fragment of a network packet is mapped from a set of descriptors
that is used by the controller to do the DMA transfer. This means that
the packet is not necessary sent when the send() function returns. For
that reason the driver calls net_pkt_ref() on the packet to prevent it
from being freed. It is then unreferenced with net_pkt_unref() in the
TX ISR when the packet has effectively been sent.
However this doesn't work if the packet is modified in the meantime,
like it will be done in PR #12563 to remove the Ethernet header
contained in the first fragment. To avoid that, call net_pkt_frag_ref()
on each fragment of the packet, and unreferenced them with
net_pkt_frag_unref() in the TX ISR when the packet has effectively been
sent.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The function to set channel alarm is called counter_set_channel_alarm.
To match the name of the function performing the reverse operation this
commit renames counter_disable_channel_alarm() function to
counter_cancel_channel_alarm().
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The controller does not support trigger. However, the check for
this condition was incorrectly (as GPIO_INT_LEVEL is 0). So fix
it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Interrupts default to trigger on level for historical reasons, so use of
GPIO_INT_LEVEL` as a mask results in a zero value. Use a mask macro to
isolate the trigger configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use the new i2c_write_read() wrapper to simplify the code.
Also add several overlays used to test the sensor on a variety of
boards, and conf file support for trigger testing.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Replace the sole use of i2c_burst_read_addr with a more generic API
function to allow the former to be deprecated along with its unreliable
sibling write and update functions.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Provides a STM32 RTC driver using new counter API.
Driver does not support wrap related functions (set, get, ..)
Fixes#11373
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CMSDK Dual Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the dual timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the single timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables debug logging in the counter_basic_api test. Fixes a build error
in the nrf counter drivers when logging is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux rtc driver to adapt it to the zephyr
counter interface. Portions of this driver are reused from the existing
rtc driver in drivers/rtc/rtc_mcux.c.
The hardware supports a single alarm only and a fixed wrap value.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In case of default top value, driver was calling top value
callback only on the first period. This was not expected behavior.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add shim driver for i.MX EPIT (Enhanced Periodic Interrupt Timer)
peripheral which can be used for i.MX6SoloX, i.MX7D and other i.MX socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Renamed:
- counter_set_wrap to counter_set_top_value
- counter_get_wrap to counter_get_top_value
- counter_get_max_wrap to counter_get_max_top_value
Updated nRF implementations and counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Modify alarm callback to return user_data and channel_id.
Set_alarm and disable_alarm updated accordingly. Renamed
counter_*_ch_alarm to counter_*_channel_alarm. Updated test
and nrf implementations.
Updated doxygen comments.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Kumar Gala