Probably left over from old ZOAP library. Stripping of headers
not required now.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Removed unwanted code, fine tuned a bit. Original use case of
sample (verify CoAP GET, PUT and POST methods) against coap-server
not changed.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If client removes observer then it reply with RESET message for
further observer notifications. That means coap-server should stop
sending further notifications to the client.
Current sample unref the packet as soon as it finds pending message
and doesn't bother about message type.
Fixes: #6534
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This adds example and testing code for CAN driver.
Tested on stm32f072b disco.
Examples are given for:
- can_configure
- can_attach_isr
- can_attach_msgq
- can_send
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds a sample application using OpenAMP for remote procedure
calls on the LPCXpresso54114. It is adapted from the RPMsg-Lite sample
application added in PR #5960, and uses the IPM driver to provide
interprocessor interrupts.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Test ArgonKey board. It provides an example of how to test
all the sensors on-board. It currently enables by default
following sensors:
LPS22HB pressure/temp
HTS221 humidity
LSM6DSL accel/gyro plus LIS2MDL magn connected to it.
VL53L0x proximity
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Minimal driver for ILI9340 LCD display driver including support
for adafruit 2.2" LCD display (1480)
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Enable CONFIG_NET_DHCPV4, while keeping static IP configuration,
which allows the app to work both with static IP (e.g. when
connected to a workstation without DHCP server) and with DHCP (e.g.
when connected to a router). When using DHCP, getting an address
may take some time, during which getaddrinfo() may fail due to a
timeout. So, add retries for this call.
Tested with qemu_x86 (non-DHCP) and frdm_k64f (both DHCP and
non-DHCP).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add MCUX IPM sample application. It can be run on lpcxpresso54114
board at the moment.
We first build the slave core image out of the remote/ dir than the
primary core image is build which includes the slave core image.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If coap-client(e.g. RPL BR) wants to get notifications from
coap-server(RPL-node) about parent status, client has to register
observer for notifications.
RPL node application modified to toggle the LED. Do not maintain any
ON/OFF states. Also removed Sparrow (contiki border router) related
patch.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add CoAP client to RPL BR application. Which can be used to
control leds and get rpl related information from leaf nodes
though CoAP messages. Build toplogy matrics and send it to
Web UI.
Enhanced Web UI components (Interfaces, RPL, Neighbors, Routes
and Topology tabs). Added buttons to control leds on lead nodes.
Added JSON support to handle led on/off requests from UI.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This is a very simple RPL border router sample application.
It provides HTTP(S) and net-shell interface for getting admin
information about neighbors and routes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
L2 could take advantage of such hardware capability, when supported by
the device. This is also required for OpenThread.
Fixes#5714
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Exclude usb_kw24d512 from wpanusb sample until the the sample
has been reworked and is more generic.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Enabling relevant hardware, currently only winc1500 on
quark_se_c1000_devboard. But it could be easily extended to other
drivers/boards.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use zephyr-app-commands for portability instead of assuming Make and
Unix, and add a missing "run" goal.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Use zephyr-app-commands for portability instead of assuming Make on
Unix, also adding a missing "flash" invocation.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Printing the output length for all encryption/decryption operation will
make it easier to know if a particular crypto driver shim provides this
information. TinyCript and mbedTLS were not providing this, making the
out_len field useless.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Add a sample.yaml file for Nordic platforms (QEMU is not supported due
to the lack of flash partitions), both nRF51 and nRF52.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If the incoming packet fragments doesn't have any link layer
header then build_reply_pkt() will set reply packet fragment's link
layer header space to zero. Which is causing issue in case of IPv4.
ARP layer is trying to fill Ethernet headers, but fragments
ll header length is set to zero.
Just use net_pkt_copy_all() to copy payload. That should be enough.
Fixes#6564
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This is required to test the server with ab (ApacheBench), which
itself is an important integration test for the IP stack.
Fixes: #7377
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Using OMA Technical Specification LwM2M Enabler 1.0.2 dated
Feb. 9, 2018, let's mark the OPTIONAL resources for an LwM2M
Device object (Section E.4 "LwM2M Object: Device")
As a result, the Device object no longer configures the default
buffers for data storage of several optional resources.
The LwM2M client sample is also changed to to setup these read-only
buffers instead.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
This adds the "old" (pre-windows8) way of doing microsoft-
specific USB descriptors, alongside the v2.0 way of doing
the same.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
This adds some vendor-specific microsoft USB descriptors, which
makes the win8/win10 enumeration process to report a "WINUSB"
capability, which in turn automatically binds a WinUSB.sys driver
to a specific set of interfaces. This, in theory, makes userspace
drivers easier to handle in win32/win64 platforms.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
In samples, using CHECK() helper macro, make it exist in case of
error. This makes sure that negative value (error indicator) can't
be passed as argument to other function and fixes Coverity reports.
Coverity-CID: 183062
Fixes: #6101
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The application started to send data before it had any IP
address configured. This prevents communication to the server.
Fixes#7502
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Zephyr supports fatfs, nffs and fcb as storage layer. fatfs and nffs
are less suited for application in memory restricted IC's. fcb has a
smaller footprint but has a complex api.
The proposed module is a module with a even smaller footprint compared
to fcb and a simple interface for reading and writing entries. The
module provides wear levelling of flash. This allows the module to be
used not only to store configuration settings but to store device state
(e.g. state of a light switch over reboots) of a zephyr device.
Fixes buffer overflow by introducing maximum read length in nvs_read()
and nvs_read_hist().
Fixes nvs_write() not to reflash the same data. Allows the user to do
call nvs_write() for all defined entries without worries about flash
wear.
Fixes garbage collection error where wrong data could be copied.
Add nvs_delete() to allow deleting a stored entry. A deleted entry will
not be copied to a new flash sector
Include flash wear information in the README.md documentation
0/25 Update module after reviewers remarks, added documentation to
nvs.h, removed README.md by nvs.rst in doc/subsystems folder
04/26 Update module after reviewers remarks, updated nvs.rst, added more
documentation to samples/subsys/nvs/src/main.c, updated doxygen info
in nvs.h (hope this time it works).
04/26 Update subsystems.rst to include nvs.restart
04/27 Updated nvs.c and nvs.h to avoid a possible flash deletion loop
when the file system is full.
04/29 Updated nvs_write to detect and ignore deletes of non-existing
items
05/06 Update NVS module to return standard error codes, removed low
level API, added configuration options. NVS now uses the board dts to
determine the flash storage location (FLASH_AREA_STORAGE_OFFSET).
05/06 Update nvs.rst. Updated intendation and added intermediate
variables in nvs.c to make the code easier to read.
05/06 Update nvs.rst.
05/07 Update nvs.rst
05/08 Changed the API to a more standard file system API.
05/08 Removed cnt_max from nvs_read() as it is not used.
05/08 Removed #ifdef(CONFIG_NVS_LOG) from nvs_priv.h, now the module can
be build with debugging off.
05/09 Removed configuration options for SECTOR_SIZE, SECTOR_COUNT and
MAX_ELEM_SIZE. It is now easy to support multiple NVS filesystems on
one or multiple devices. Changed logging to support newlib systems.
Thanks to Olivier Martin for reporting and proposed changes.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Due to higher traffic demands when using 6lowpan, we should raise
the default BT RX buffer counts and sizes.
This avoids the following error on some HW:
[net/buf] [WRN] net_buf_alloc_len_debug: bt_buf_get_rx():4985:
Pool 0x20009424 low on buffers.
[net/buf] [WRN] net_buf_alloc_len_debug: bt_buf_get_rx():4985:
Pool 0x20009424 blocked for 0 secs
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Make sure that we compile sanity checked application with
more config options in order to catch compile issues faster.
In this case DHCPv4 + debugging options are enabled for
sanity checker.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If DHCPv4 was enabled, then there was compile error as the code
was still using wrong variables.
Fixes#7342
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This ensures the every characteristic has a value attribute declared
with the same UUID since the old macro did not declare the value the
application would normally have to declare one itself using a different
UUID which is not allowed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The sequence number was acting as a stop-gap for missing persistent
storage. Now that we have the settings support in place it's no longer
needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable BT_SETTINGS and remove any custom flash access used for the
sequence number. We do settings_load() before bt_mesh_provision() and
use the return value from the latter to identity that settings_load()
had recoved a full configuration.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Keeping the model struct same sized, change the element pointer to two
indexes, and add a flags member that will be used to track pending
storage actions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having an RPL-specific storage timer, introduce a generic
one that'll eventually be used for all persistent storage.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
NET_APP settings was missing the device name and enabling the net shell
is nice to verify runtime configuration as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add initial skeleton for doing settings-based persistent storage for
the mesh network state. This patch only includes restoring some core
network state such as IV Index, Sequence number, Net Keys, App Keys
and the Replay Protection list. The remaining state, and actually
storing the state, is left for follow-up patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Header was missing after merging PR #6970
`Add support for File System multiple instances`
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Assign the appropriate disk name Kconfig option to the
usb mass storage sample test.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Ravi kumar Veeramally