Instead of enabling Bluetooth by default on nRF5x boards, only enable
the controller if Bluetooth has been enabled by the applicaiton.
Fixes#5454Fixes#12215
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
I removed GPIO configuration from board files and enabled them
as default in driver Kconfig file. All boards had GPIO ports
enabled that is why I decided to enable it by default.
Power management example was changed to use new driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
UART driver renamed to keep the same convention as SPI and TWI drivers.
All substrings: "UART_NRF5" in defines renamed to "UART_NRFX_UART".
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
+ VBLUno51 board
nRF51822
Bluetooth Low Energy
DAPLink interface
UNO pinout
4 power
+ Wiki: https://vngiotlab.github.io/vbluno/
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Carles Cufi