Default BT_RX_BUF_COUNT value is not enough when transfering a large
amount of data (e.g. heavy network traffic over BT 6LoWPAN). Increase
BT_RX_BUF_COUNT from default value 3 to 10.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Be sure to check for NULL pkt in receive callback, which means TCP
EOF. The fix ported from echo_server sample.
Jira: ZEP-2423
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add cross-referenced information on the 96b_carbon and
96b_carbon_nrf51 pages which disambiguates between the two "boards".
Also describe how to flash 96b_carbon_nrf51 with
samples/bluetooth/hci_spi and 96b_carbon with samples/bluetooth/ipsp
to support a Bluetooth HCI stack on 96Boards Carbon (the physical
board).
While we're here, make the documentation page for 96b_carbon match the
format in doc/templates/board.tmpl.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Various of the printk messages in this sample app don't have
newlines. Let's fix the output by moving to SYS_LOG_xxx() macros
instead, which don't need them anyway. This also makes it easier to
tell errors apart from other messages, etc.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Add a sample application that allows a Zephyr-based Bluetooth
controller to interface with an HCI driver via SPI. This sample
implements the same BT SPI protocol already as Zephyr's HCI SPI
driver.
Currently, the sample only supports the legacy SPI API.
Provide a single configuration file, avoiding board-specific
files. Some board-specific configuration information must be provided
via other means:
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_PIN
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The parsing of strings with sharp notes (e.g. "100C#") was incorrectly
implemented. Now it should be correct. Additional benefit is that this
should fix Coverity CID 173632.
Jira: ZEP-2467
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Make use of CONFIG_NET_APP_BLUETOOTH_NODE to enable advertising and
registering the necessary services.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Count of 4 seems to cause deadlocks with some Android phones due to
other GATT activity in addition to Mesh related data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an app uses a construct such as:
obj-y = main.o ../../../../samples/bluetooth/gatt/hrs.o
in its makefile, it causes said object module to be built in the
source tree, not in the object tree.
When building massively parallel, this usually resuls on the files
getting corrupted, leading to bugs such as:
https://jira.zephyrproject.org/browse/ZEP-2316https://jira.zephyrproject.org/browse/ZEP-2317
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:3: warning: NUL character seen; rest of line ignored
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:4: warning: NUL character seen; rest of line ignored
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:5: *** missing separator. Stop.
as multiple build are trying to touch the same file in the source tree
and of course, race and causes a build bug.
We have known about this issue for a long time, but it requires
modifications in the build system that there is no time to tackle.
A suggested workaround is to include the source files into a local .c
file, so this is what this patch does, to remove the random noise.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
There's no need for debug logs by default in the mesh sample, and it
just contributes excessively to the ROM footprint.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Not easily done using RAM/ROM filters, configurations need to be adapted
to make this fit on more devices. Limit the target platforms now while
we figure out configurations.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This sample includes builtin UDP and TCP echo servers, max
MAX_CONTEXTS=3 as set previously, they just didn't work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add an initial implementation for the Bluetooth Mesh Profile
Specification. The main code resides in subsys/bluetooth/host/mesh and
the public API can be found in include/bluetooth/mesh.h. There are a
couple of samples provided as well under samples/bluetooth and
tests/bluetooth.
The implementation covers all layers of the Bluetooth Mesh stack and
most optional features as well. The following is a list of some of
these features and the c-files where the implementation can be found:
- GATT & Advertising bearers (proxy.c & adv.c)
- Network Layer (net.c)
- Lower and Upper Transport Layers (transport.c)
- Access Layer (access.c)
- Foundation Models, Server role (health.c & cfg.c)
- Both PB-ADV and PB-GATT based provisioning (prov.c)
- Low Power Node support (lpn.c)
- Relay support (net.c)
- GATT Proxy (proxy.c)
Notable features that are *not* part of the implementation:
- Friend support (initial bits are in place in friend.c)
- Provisioner support (low-value for typical Zephyr devices)
- GATT Client (low-value for typical Zephyr devices)
Jira: ZEP-2360
Change-Id: Ic773113dbfd84878ff8cee7fe2bb948f0ace19ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This disable debug options in order for the image to fit in boards
such as arduino_101 and quark_se_c1000_devboard.
For convenience this adds another configuration file with as it was
available previously which can be build using:
make CONF_FILE=prj_dbg.conf
JIRA: ZEP-2378
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since the controller comes with a transmit buffer size that mirrors the
maximum size of a transmit packet, use that to size the buffers that are
used in the hci_uart application to receive packets from the Host over
the UART.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The worst-case maximum number of CCC entries we need is actually
MAX_CONN + MAX_PAIRED. Provide a helper define for it and use it
whenever appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Explicitly select CONFIG_BLUETOOTH_BROADCASTER and
CONFIG_BLUETOOTH_OBSERVER in the scan_adv sample.
If the Controller is included without connections support
then only broadcaster support is compiled in by default,
hence add broadcaster and observer role support explicitly
in the prj.conf file.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This patch allows more generic USB configuration in the samples
and removes platform dependent driver configuration.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We have many testcases doing filtering both on the architecture level
and the platform level, which is redundant. Also many testcases are
running the same test twice on the same SoC for no good reason, cleanup
the tests and cleanup the filtering.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
With the introduction of privacy, the system workqueue is now being
linked into the image, growing the RAM footprint considerably.
In order for the sample to fit in QFAA and QFAB variants of the nRF51
(16KB of RAM) we reduce the workqueue stack size to 512 since the RPA
update mechanism doesn't use more than 340 bytes and we stick to 16
connections maximum.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This will prepare test cases and samples with metadata and information
that will be consumed by the sanitycheck script which will be changed to
parse YAML files instead of ini.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds bt_gatt_register_service using bt_gatt_service which contains
the attribute array that is then added to the database saving a pointer
in each and every attribute declared.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GAP is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes CONFIG_BLUETOOTH_GATT_DYNAMIC_DB in preparation to the
introduction of bt_gatt_unregister.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enabled testing CONFIG_BLUETOOTH_SHELL with configuration other
than btshell and enables ipsp sample to use bt shell module which
allows to disconnect, print metrics, etc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Passkeys are always 6 digits in length and should therefore be
zero-padded if necessary.
Jira: ZEP-2113
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since most of nRF5x-based boards can be used either as a standalone
development kit or as a BLE controller to connect to an external host,
add DT overlays so that the baud rate is correctly set to 1Mbit/s
whenever building the hci_uart sample application.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08c682bfc0b80dfa88de859e90a011bcd2db2762
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some incompatible changes were introduced when net and bluetooth
branches were changed at the same time.
Change-Id: Ifa03f85d26a63ade0fcc029377d54850c0e92451
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Ricardo Salveti