Not all boards are going to have the ccs811 on them, and thus not in the
device tree. We need a dts.fixup stub to dummy out the CONFIG_CCS811_*
defines that the driver expects.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sample application for AMS CCS811 digital gas sensor driver.
This application fetches Co2, VOC, Voltage and Current readings
from the sensor and prints it on serial console continuously.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
SENSOR_CHAN_DISTANCE is now in meters. Print value in meters, as
double, this requires printf() and CONFIG_STDOUT_CONSOLE. This is
similar to how other sensor samples have it.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This sample application allows to test vl53l0x distance sensor.
By default it is built with disco_l475_iot1 board as it is
built-in.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Since no GPIO trigger is configured in hts221 sample application,
update prj.conf to enable TIGGER_NONE flag
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove build_only and add harness type needed for the sample/test to
allow running with sanitycheck and on devices once we have harness
support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
To test BMM150 geomagnetic sensor driver in polling mode,
sample application added by this patch can be used.
Signed-off-by: Punit Vara <punit.vara@intel.com>
Sample can be used to test ambient light, RGB and proximity
functionality of APDS9960 sensor in polling mode.
Remove old sample which is not using sensor API.
ZEP-1552
Signed-off-by: Punit Vara <punit.vara@intel.com>
We have many testcases doing filtering both on the architecture level
and the platform level, which is redundant. Also many testcases are
running the same test twice on the same SoC for no good reason, cleanup
the tests and cleanup the filtering.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will prepare test cases and samples with metadata and information
that will be consumed by the sanitycheck script which will be changed to
parse YAML files instead of ini.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some files have moved from their original location, or are no longer
available. For the mbedtls samples, tweak the link to point to a page
where links for current and previous downloads can be found.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This commit provides sample application for sensor hts221.
By default, it is enabled on board disco_l475_iot1
Change-Id: I535fac8a670fa89cc1cae15ea1abe9cfe4b6c56b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08c682bfc0b80dfa88de859e90a011bcd2db2762
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a max30101 sample application that polls sensor data and prints it
to the console.
Jira: ZEP-720
Change-Id: I50f28eaf9ea2ff5bfbb9fb6922c4006d5c02e739
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Docs need a label at the top so we can use :ref:`labelname`
to create a link to that doc from other docs.
Change-Id: I37c654fb0bb7ebdf288af01e41ce5497969f8968
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Updates the fxos8700 sample documentation to include board
cross-references and sample output with temperature data.
Change-Id: I8d4e4d8d287806f5480316da09d4072fcf9c05ac
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a fxas21002 sample application that uses the sensor data ready
trigger to periodically print gyroscope data.
Jira: ZEP-1392
Change-Id: Ic9d3803a41f2873aef470a2a73b3f1db44d39b50
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the temperature sensor in the fxos8700 sample.
Change-Id: I2b4c306d3c5528dc32d940476c00180b5df08187
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kumar Gala