In initial state of the system it is possible that no backends are
yet enabled and log processing is triggered. In that case logs were
discarded. A flag has been added to the log core to do processing
only if at least one backend is enabled. It is applicable only to
initial phase. If backends are disabled in application lifetime
logs will be discarded.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended macro to accept flag indicating if given backend must be
initialized and enabled when log subsystem starts. Typically, simple
backends will have autostart flag set. More complex may require
explicit enabling (e.g. shell over BLE can only be enabled when
BLE connection is established).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
We are using a non-32-bit aligned value as the block size
when initializing the strdup mem_slab for Logger.
When the non-aligned pointer is being freed, it's converted
to a u32_t and this generates the following:
***** USAGE FAULT *****
Unaligned memory access
Let's use the aligned buffer size as the block size instead.
Signed-off-by: Michael Scott <mike@foundries.io>
If user will enable shell than for each backend shell instance
will be created automatically.
Update all shell examples according to the new initialization
procedure.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
When using composite devices, an error is printed during the
initialization:
| [00:00:00.000,000] <err> usb_device: set cb, ep: 0x81
|
| [00:00:00.000,000] <err> usb_device: set cb, ep: 0x1
|
| [00:00:00.000,000] <err> usb_device: set cb, ep: 0x82
|
| [00:00:00.000,000] <err> usb_device: set cb, ep: 0x2
This is actually not an error, but rather a debug message. In addition
it should not contain a new line as it is automatically added by the
logger subsystem.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
usb_dc_status_callback() parameters are interface or configuration
numbers and should be const.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adding status callback allows to control report sending only when i.e.
device is connected or configured.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If we receive a valid gratuitous ARP request, then update ARP
cache accordingly. This feature is optional and by default
it is enabled, but can be turned off if needed.
This is similar to a feature available in Linux, and is enabled
by default in many distros.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some terminals literally interprets shell output data. Hence to print
a message in new line shell needs to send `\r\n` each time. To minimize
flash usage user can now send `\n` as a line delimiter and shell will
automatically add missing CR character.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The wifi mgmt does only support TCP/IP offload wifi chip,
while non-offload wifi chip can not scan/connect to AP.
Signed-off-by: Dong Xiang <dong.xiang@unisoc.com>
Placing it at sys/fcntl.h was due to mimicking internal newlib's
layout, but what we need is this file at the standard location,
for reuse.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
USB controller was performing the fragmentation by itself and the driver
was not aware if current chunk is the last one if data size is equal to
maximum chunk size. Some hardware controllers (i.e. in nRF52840) handle
the status stage by hardware which must be triggered after the last data
chunk.
Currently, the whole remaining data is passed to the driver, and the
driver decides whether to fragment the data internally, or send only
the chunk and report back to the stack.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
This commit fixes the issue that if a thread is waiting on recv for
data and the user closes the socket, the waiting thread is not
unblocked.
Signed-off-by: Léonard Bise <leonard.bise@gmail.com>
This commit adds missed const modifier for addr pointer for
bt_le_set_auto_conn function
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
Rename log level variable:
CONFIG_LOG_IMG_MANAGER_LEVEL to CONFIG_IMG_MANAGER_LOG_LEVEL
Use template for log levels.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Refactored the fix in the commit 685da02354 ("Bluetooth:
controller: Fix advertising random delay resolution calc")
to apply modulo in tick units before adding a tick.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix bluetooth config dependencies where the definitions depend on other
definitions.
BT_RX_PRIO is not always defined in a controller only build.
BT_CTLR_TX_BUFFER_SIZE does not depend on BT_CTLR, but BT_LL_SW.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This header is private data and we shouldn't (and aren't) using it in
the tracing_sysview.h. SystemView tracing works fine without it, as
tested with the philosophers sample.
This commit fixes the build when bluetooth SMP and SystemView tracing
are used, because the kernel_structs.h inclusion ends up pulling in
kernel_internal.h, which declares smp_init(), whose declaration
conflicts with another internal routine by the same name in
subsys/bluetooth/host/smp.c.
Signed-off-by: Marti Bolivar <marti@foundries.io>
The wifi management interface was still using one SYS_LOG_DBG
macro call, replacing that with NET_DBG.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding spaces around "=" when definining Kconfig template so
that is more consistent with overall style of these template
variables.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calling bt_recv in the Bluetooth host Tx thread by the
controller implementation caused deadlock in combined host
controller builds when HCI LE Create Connection Cancel
generated the HCI LE Connection Complete or HCI LE Enhanced
Connection Complete events.
Controller's HCI implementation has been updated to place
the generated event into Rx FIFO to avoid the deadlock.
Relates to commit a59f544fb4 ("bluetooth: controller:
Handle non-priority events correctly")
Relates to #10314.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
bt_conn_disconnect removes device from autoconnect list and thus
should not be called from le_conn_update when timeouting pending
connection. Also auto connect flag needs to be check on connection
failure to make sure scan is restarted.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
In commit d5836195d7 ("Bluetooth: controller: Increase advertising
random delay resolution"), the resolution of random_delay was
increased from 8-bit to 16-bit. Due to this switch the result
of HAL_TICKER_US_TO_TICKS() can now be a 0, which causes the following
crash:
***** Kernel OOPS! *****
Current thread ID = 0x200043f0
Faulting instruction address = 0x17914
Fatal fault in ISR! Spinning...
Let's make sure we don't pass a 0 to ticker_update() by increasing
the result of HAL_TICKER_US_TO_TICKS() by 1.
Signed-off-by: Michael Scott <mike@foundries.io>
Added functionality to enable active shell backends via Kconfig
file. When there will be more backends implemented user will
have an option to select only required ones.
It is no longer needed to select SERIAL in prj.conf.
Fixes#10190
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As the debugging print calls are async, all the strings that might
be overwritten must use log_strdup() which will create a copy
of the printable string.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was trying to print peer IP address string but that
pointer could contain garbage. There is actually no need to print
anything in this case, the error code return is enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently logging subsystem supports quite small number of function
parameters. So split some long functions into smaller pieces.
Hopefully this is just a temporary patch and we can support more
parameters to logging macros.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Krzysztof Chruscinski