This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux uart driver to adapt it to the Zephyr
serial interface. Unlike the existing (and confusingly-named) uart_k20
driver, this driver can be used for k64 and other Kinetis SoCs.
Implements polling and interrupt-driven serial interface functions that
are logically equivalent to the uart_k20 driver. Adds an extra instance,
irq_tx_empty(), and err_check() that aren't implemented in the uart_k20
driver.
Jira: ZEP-719
Change-Id: Iab99542e7ec921ef4f361437768113fee01e5fe8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
riscv-qemu UART:
1) comprises only one register that is used to send or
receive characters in a polling fashion.
2) does not have a FIFO and is not interrupt-driven.
Change-Id: I9408f1776eba4cec4aa203a5da759ec04bcddf1f
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Add driver for CMSDK APB UART ports. The driver implements RX and TX
functionalities. Data transmission is implemented using polling and
interrupts. The driver default configuration for the port is to use
8bit data transmission, 1 stop bit, no parity control.
The driver exposes a public uart driver API and allows to register up
to five UART devices: from 'UART_0' to 'UART_4'. The driver performs
the required pinmux, the clock control configuration is left to the
platform.
The driver has been verified to work with the Hello World sample
application on a Beetle Board.
Jira: ZEP-1245
Change-Id: I5baf78b7659aae2a574d8e66205e6fd5eb579133
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This currently only supports outgoing messages without interrupts.
Change-Id: I635562f47106eb6cdc7104a8160e431bebea25dc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add driver for U(S)ART ports on STM32 MCUs. The driver implements basic
RX/TX functionality. Data transmission is implemented using polling. The
driver configures the port to use 8bit data transmission, 1 stop bit, no
parity control.
The driver exposes a public uart driver API and registers a single UART
device 'UART_0'. The device binds to USART1 peripheral and performs
required pinmux and clock control configuration. The device can be
initialized at the PRIMARY level, with default device priority.
The driver has been verified to work with a sample Hello World
application on a STM32F103 series MCU.
Change-Id: Iae103fcd8d2fb0a6c173cf141a68e17791255aab
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
This patch introduces the QMSI UART driver which is simply a shim driver
based on UART driver provided by QMSI BSP.
This initial version implements only the mandatory APIs 'poll_in',
'poll_out' and 'err_check' which are required by trivial sample apps and
by output functionality from the console driver. The remaining APIs will
be implemented by up coming patches. The driver supports only 115200 baud
rate at the moment.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_SERIAL=y
CONFIG_UART_QMSI=y
This driver has been tested with Quark SE Devboard so this patch also
adds its platform-specific default configuration options to 'arch/x86/
soc/quark_se/Kconfig'.
Change-Id: Ibde1825d4b0349a376a8e7d91cc9de306946b62f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds CONFIG_UART_NSIM to enable the uart/nsim driver.
This fixes compilation issue where the base address parameter
is not defined due to CONFIG_NSIM=y but CONFIG_SERIAL=n.
Change-Id: I1dc1c15b22ad174d4db514d89551780f0dfcae66
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove unused code after refactoring all the serial/UART drivers.
() Since device initialization is done by the drivers themselves,
there is no need to have config_func(), port_init() and uart_init()
to perform configuration external to driver. So remove the related
bits.
() The IRQ priority is only being used when doing IRQ_CONNECT_STATIC().
So there is no need to send it over during uart_init().
Change-Id: I72eb3402036b53cbc01c1eb968de0ddfa0096ee2
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Rename nsim_uart.c to uart_nsim.c. This is to follow
the driver naming convention.
() Rename functions nsim_uart_*() to uart_nsim_*(),
following driver naming convention.
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: If015f39a6f6b4fcc65625e6e5f973b4469202f54
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Renames stellarisUartDrv.c to uart_stellaris.c. This is to follow
the driver naming convention.
() Renames functions stellaris_uart_*() to uart_stellaris_*(),
following driver naming convention.
() Renames CONFIG_STELLARIS_UART* to CONFIG_UART_STELLARIS*
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: I0eadc3878d69ff24d1637f8df5220fd2f161d24f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Rename k20UartDrv.c to uart_k20.c. This is to follow the driver
naming convention.
() Move driver/serial/k20_uart.h to drivers/serial/uart_k20_priv.h
as this contains definitions private to the driver, and
should not be exposed in public include directory.
() Rename functions k20_uart_*() to uart_k20_*(), following
driver naming convention.
() Renames CONFIG_K20_UART_* to CONFIG_UART_K20_*
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: If1be1fde083aba6ff68062db2059aef08617a286
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Renames ns16550.c to uart_ns16550.c. This is to follow
the driver naming convention.
() Renames functions ns16550_uart_*() to uart_ns16550_*(),
following driver naming convention.
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
() Renames CONFIG_NS16550_* to CONFIG_UART_NS16550_*
() Disable NS16550 for ARC as no port is defined anyway.
Change-Id: I76bbe25b9bc75eb62df81e533f84f4f63a5257b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This restructures the device structs and now utilizes the new
driver initialization model. This is another step towards
converting the serial driver to the new driver model.
Note that the serial driver does not initialize the hardware
unless it is being used by another driver. The configuration
of the serial port needs to be done by the driver utilizing
the port (e.g. baud rate, interrupt priority, etc.).
Therefore, some serial ports are declared but not exactly
configured.
Also note that the UART console is being initialized at
the same time as the serial port. This will be removed
in future patch, so the UART console driver will do
its own initialization.
Change-Id: Idd89954b2d0649a557ba8c869ee96512fec898e4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
All driver Makefiles are adding the same cflags and they
have been done inconsistenly, make all drivers inherit
from the top level Makefile and remove unused includes.
Change-Id: Ie66d0ba7a418ac26f7eb709f50c887dc682e935c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Updates references to CONFIG_BSP_DIR to CONFIG_PLATFORM as part of the
BSP -> platform clean up.
Note that despite the renaming, the usage of the config option remains
unchanged.
Change-Id: I2846c3f761cf09871019c0855bf1824ae03e6b3c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
According to section 3.7 of Documentation/kbuild/makefiles.txt, using
EXTRA_CFLAGS in Makefiles is "still supported but their usage is
deprecated." However, using make EXTRA_CFLAGS="-DSOMETHING" results in
EXTRA_CFLAGS from Makefiles being overwritten, obviously breaking the
build. This patch converts to them to the newer ccflags-y which also
fixes the problem.
Change-Id: I6309439599d4c9cc184f9ecd941bde841982ef07
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adaptes the Kbuild system to the change of location of
the header files for drivers.
Old location: driver/
New location: include/driver/
Change-Id: Ic49d373149ee44d781419c5c68e59408c8ef1c11
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit adds the Makefiles that describe the object-bundles
for the drivers directory and every subdirectory below.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Id77cff9cf0ab51827acc2aef32cbed3ec3ad586b
Leandro Pereira