Replace precision formatter (.) in printk with padding flag like %04x
since for now precision is not handled properly in printk family.
Change-Id: Ib63198e407ef584c5650d6452518b1767047630f
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
After some more careful measurements, the worst measured overhead is
288 bytes. Adjust BT_STACK_DEBUG_EXTRA correspondingly to 300 (to give
a bit of playroom still on top of this).
Change-Id: Icdf477b05b40917027314b180c2b69c8c6c759b3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These should have been converted to using printk instead.
Change-Id: I62323704dad4fc51cc14ee4734acb6b325dcda14
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
BT_STACK_DEBUG_EXTRA was adjusted by commit 047c6eacf7,
however it failed to cover this #ifdef section in log.h.
Change-Id: I1a9cd81dc25e9465daba62f0116b2661ac047362
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is used to disconnect a dlc.
Syntax:
>br-rfcomm-disconnect
Change-Id: I8f345d9fbb1f1f84bfb1f697322d9a87ff531797
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
This will be used by the user to disconnect or cancel connect dlc.
This also defines an internal close function which will take
appropriate action based on the dlc state.
In case of user initiated disconnection if some pending packets are
there in queue then it has to be sent before sending DISC packet.
< ACL Data TX: Handle 256 flags 0x00 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x2b cr 1 dlci 0x0a
Control: 0x53 poll/final 1
Length: 0
FCS: 0x6d
> ACL Data RX: Handle 256 flags 0x02 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x29 cr 0 dlci 0x0a
Control: 0x73 poll/final 1
Length: 0
FCS: 0x26
Change-Id: Ie4fa3bd8f6b279fee6fb56ddce198d82c5047849
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
We can locally reference the files we need, so don't add a -I we
don't need.
Change-Id: I764aea4177a8995489e0f15f71f7373427b43394
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When PSM server doesn't have BR/EDR L2CAP resources to assign and handle
incoming request properly, local channel pointer may stay uninitialized.
This fixes such scenario. The fix refactors main connection request
reply handler to additional helper which can be used to send response
unconditionally for situation when local channel is not allocated
to setup L2CAP link between.
Jira: ZEP-1405
Change-Id: I5caedd63a59ad0d1704ac87fa51616a0770320bf
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Now that printk is the default backend for logging the overhead is not
as bad as with printf. 160 seems to be roughly the worst case amount
of overhead that debug logs now cause.
Change-Id: Ia5937b7318e00cc31c72fa1702c73a57bca0603a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of %4.4x we need to use %04x which printk supports.
Change-Id: I0564be5531bb266b328f77231f5d00f43eabe1ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of %2.2x we should use %02x since printk doesn't (currently)
support the former.
Change-Id: I773972e63071b81c95c65de292f12ab14d7c310b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If connection destination address has been changed update the addresses
stored by the time it disconnects since in case of RPA it is no longer
mapping to the same device after it has been disconnected.
Change-Id: I0ce966928f605a885125179eaa7b9093989825ab
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The connection destination address may change if the identity address
is resolved.
Change-Id: Id6f7b6494c24ff118043ba5f4ff54e254376eddf
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_conn_lookup shall work both with identity address or initial
destination address as bt_conn may change the destination address with
the identity address.
Change-Id: Ibdd19ec453c3307eb6db188196b7e57a2260b526
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There's now snprintk available that's more light-weight on the stack
than snprintf.
Change-Id: I6b3e4409703ca92fe6b8f4146ff47c490ab826cb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Applications may want finer control of the NRPA used for
non-connectable beacons, and provide it up-front rather than letting
the stack generate one.
Change-Id: I84d459372cc85ed09a8f9cde16dbb9b98dec2a43
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Expose helpers in hci.h for setting and getting the LE random address
type.
Change-Id: I7c6437051f0b2d1f5f79e19b2616bb643ae6300b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To guarantee that the compiler does not reorder the execution of
irq_lock() with preceding operations, a volatile qualifier is
placed before the declaration of the ticks variable, which then
ensures that irq_lock() is executed after the tick calculation but
before accessing the ready and timeout queues.
Without the volatile keyword interrupts will be disabled during the
calculation of the ticks, which increases interrupt latency
significantly.
Change-Id: I2da82a1282e344f3b8d69e9457b36a4cb1d9ec18
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The SYS_LOG macros now map to printk by default, and printk doesn't
(currently) support %2.2x, rather %02x needs to be used instead (it
gives the same result).
Change-Id: I0f7a5b7da91afba0c970bce7e2680de40c917bd3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Having the logging macros arbitrarily mapping to printk or printf
based on selected Kconfig options that the app isn't necessarily aware
of can have unexpeced (bad) side effects. In particular, printf
consumes *a lot* more stack (closer to 512 bytes) than printk, so
enabling a seemingly innocent CONFIG_STDOUT_CONSOLE option could lead
to stack overflows that are hard to debug.
Jira: ZEP-1419
Change-Id: I5fd77a7ed402e9ca67af23857e0f886f96d243bc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: I4d6f635a0ed61de698727028ea8767dc0ef28bb1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: Iab7cc6da110e9c98720211a6f773dcf055a3a411
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide PWM driver for STM32 series F1/F4/L4.
Driver is ported on STM32Cube HAL and should support other STM32
series with minor updates.
Configuration is done so that PWM sample driver could be run on
all nucleo boards supporting PWM driver.
Change-Id: I6522a565451085df932e0eefd8404268380b5bfe
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following pinmux update for PWM support,
update soc to support this new configuration.
Change-Id: I1126e347ab1ab6b2d830993e548de8f32fa2f8f9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pin config for PWM support on ST Nucleo boards
Following config is chosen:
-PA0/PWM2_CH1 for F401RE and L476RG
-PA8/PWM1_CH2 for F103RB
Change-Id: I013e15ed35360d7777bb24ff94e0830f913a6580
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds Beetle to the Watchdog test case.
Jira: ZEP-1300
Change-Id: I371ca2f89aaec8e07f45cfa04fc2618d009cf487
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch updates defconfig file on V2M Beetle board in order to enable
clock_control and watchdog by default.
It defines also a dummy LED in order to maintain compliance with the
Zephyr test environment.
Jira: ZEP-1300
Change-Id: I40ae4cb19e79ff24e1e351a2185a7191f03664d1
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds Timer 0 and 1 to be used as counters.
Jira: ZEP-1300
Change-Id: I9d8b971d8a3d76eee2f9cc4600e95729d67717a3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add driver for CMSDK (Cortex-M System Design Kit) APB WDOG. This device
uses NMI as interrupt hence it requires Runtime NMI (CONFIG_RUNTIME_NMI)
to be configured in the platform.
Tested with drivers/watchdog sample application.
Jira: ZEP-1300
Change-Id: Ib318047109af81e32060e80d456ef3873fd380ea
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
CMSDK APB UART driver.
Jira: ZEP-1300
Change-Id: Ic0a214beb02d56ffb02ad4e6ca26b80805c0a4e6
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
Beetle GPIO driver.
Jira: ZEP-1300
Change-Id: I576767b68a8e4aa965d34716528df3bb4e837d73
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the clock_control implementation for the ARM LTD
Beetle platform.
The main features enabled are:
* Clock on and off in ACTIVE, SLEEP and DEEPSLEEP mode.
* PLL support (freq: 12, 36, 48 Mhz).
The integration with the existing drivers will be done in future
patches.
Jira: ZEP-1300
Change-Id: I07cb2325275bd86a036e8e24aeb7bbf2c6176a93
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the boot time Power Management configuration for Beetle
on Zephyr. In particular it defines the states of the peripherals during
sleep and deep sleep and the allowed wakeup sources.
Jira: ZEP-1300
Change-Id: Iad9c0f851771ea60d94bbe5420b7b3ee0743b77e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the I2C for the STM32Lx series
Change-Id: Id1694aeb3606b4fa9772bfb7a9f60e48a7cc93a8
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add one pin configuration for I2C1 of the STM32L4 series.
Change-Id: Id05d916f2a1126ca439aebcddd8dc9c91015f6fe
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add all possible pin assignment definitions for I2C{1-3} on STM32L4xx.
Change-Id: I2d4266bc3bb9ba41b74a80567c0b04a89963753e
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the pin configuration of the USARTs.
Change-Id: Idf7a18b6eab95c61870ad4850c9eafb1fdcab03d
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add macro for all the available pinmux for the USARTs present on
STM32L4.
Change-Id: Ie4352750e1c6f08642b3e222b57f2a791f08ef74
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add EXTI support for the STM32l4XX family.
Change-Id: Ia92f26eaf49899ea23fae05dd3a7357007c9db20
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the support for all the GPIO port of the L4.
Change-Id: Id365e17223cd5c49443df9fb6b96a3c4f204f523
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Deal with STM32L4X additions for clock and interrupt handling to the
uart driver.
Change-Id: I6e8dafb132dafea54b8f31a3a5cb6e35a207574d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the initial SoC support for the STM32L4XX family. The code was
tested on STM32L476RG, but should work on any STM32L4XX currently
available.
This implementation was inspired by the stm32f1x implementation.
Change-Id: Id6670bce0c423617284e8467a9c461531f948e0f
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Arkadiusz Lichwa