These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The issue was introduced by commit-id 27bdb83.
RTC_DIVIDER used to be 0 by default, now it's 1.
Fixes#8098
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This patch adds a prescaler configuration option that denotes the
number of RTC ticks per second. This is used to calculate the value
for 1 second.
Signed-off-by: Andy Gross <agross@kernel.org>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit removes unnecessary CONFIG_SYS_POWER_DEEP_SLEEP protection
in shim drivers as QMSI 1.4 has introduced empty context save/restore
functions that can be called in Quark D2000, therefore keeping common
code at the shim driver level for Quark SE and D2000.
Change-Id: Ia2a466327f999668c6511c0193014e9151bff6ae
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I84a09a0aaa3a00452d8c2b4bca7be0f6b2015218
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This commit removes the RTC interrupt masking/unmasking needed after
wake up as that functionality is now available in QMSI 1.4. The QMSI
save/restore functions are called instead.
Change-Id: I15b5063fa64c71b125edd2c709410b5ae655032e
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The enum type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: I50b68e201ef6fb18a02eeda2a2e7548dad3f358c
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Change the included kernel header file from nanokernel.h
to kernel.h
Change-Id: I754b883d1769517e908e88096e7704666ec12275
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add delay to wait for new configuration to take effect before
returning to API caller. It takes time for any change to rtc
configuration to take effect since rtc runs under a much slower
clock.
Of course, we do not have an equation for best wait time.
The value is based on the test results on arduino 101, minfield
and quark se c1000 devboard(some margin added).
Jira: ZEP-991
Change-Id: I0dcee3c5809963dcd418186b85e3473427a4d526
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This commit updates the rtc_qmsi driver by modifying the temporary
Zephyr save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-1000
Change-Id: I6f77fe086ea6415a5bc2b2b21874c8a573fd7b44
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
Signed-off-by: Iván Briano <ivan.briano@intel.com>
For AON peripherals on Quark SE C1000, an API is needed
to retrieve the interrupt status after wake up.
This enables the application to know the wake source before
enabling again the interrupts.
Add this API to the rtc as this is a wake event
on Quark SE C1000.
Jira: ZEP-1188
Change-Id: Id850ce405eb3f4857be720201e462ea8e24a334f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_SCSS_INT is renamed to QM_INTERRUPT_ROUTER;
- every member of QM_INTERRUPT_ROUTER was renamed as well;
- QM_IRQ_* renamed too, mostly added _INT at the end;
- some isr functions were renamed to keep their names consistent;
- build for x86 needs to define QM_LAKEMONT, as QM_SENSOR was for ARC.
Change-Id: I459029ca0d373f6c831e2bb8ebd52402a55994d1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
In order to avoid type conflicts make sure that ISR_HANDLED
is defined. This makes the ISR the correct type.
Make sure that the pointer for the unused argument for ISR
is of the proper type (NULL).
Change-Id: Ia1873f32d2e2174085f929e318a780a1b2574785
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
In QMSI 1.2 API, the RTC divider value for the prescaler can now be set
on runtime. This is done through a config parameter for the qm_rtc
driver.
Fix the rtc shim driver by using the value defined in rtc.h as
RTC_DIVIDER.
Change-Id: I5ab61a5a1a3debca103f2782e0ac584938dc91e1
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The new device control API added a 'device_power_state' variable to the
driver's data structure to keep track of the current power state set
for a device. This member variable is conditionally built into the
runtime data structure of each driver, but in some cases the whole data
structure is conditional on its respective API_REENTRANCY config
variable.
In those cases where the runtime data was previously used only for
reentrancy protection, the runtime data pointer used for device
initialization is NULL, and when power management is enabled, this
invalid pointer ends up dereferenced to get the device_power_state
member.
Make the declaration of the runtime data dependent on any of its
conditional members, and NULL only when all of those settings are
disabled.
Change-Id: I4f41e00ad8551a096db639e31d33f43752b6672f
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Update the power sample and drivers with the new device driver power
management API using the existing logic
Jira: ZEP-954
Change-Id: Idd94232e458767635973e94e9fc673c01612c1e2
Signed-off-by: Amir Kaplan <amir.kaplan@intel.com>
Guard critical section of the driver API, so that
multiple simultaneous calls from tasks/fibers wont
corrupt the driver state.
The locking mechanism is by default disabled in the
build. To enable it, the following flag needs to be defined:
CONFIG_RTC_QMSI_API_REENTRANCY
Jira: ZEP-412
Change-Id: I430ebc07bf3277e5a5961cb6278c5500cd1e139b
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This adds some basic suspend/resume support in the rtc qmsi
driver. This is part of a change to enable device suspend/resume
and Deep Sleep support in sample application.
Jira: ZEP-512
Change-Id: I79ccfb56de5b3cbfb5bc91e9cacca68554aa46ee
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The configuration option CONFIG_RTC_IRQ_PRI does not longer exist, and have
to use the specific QMSI driver IRQ priority
Change-Id: I8074c6d8e095596d03e51a94f26a73c3a9ff91b7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
This also separates IRQ_PRI into one for DW and one
for QMSI, to follow the convention of every other
drivers.
Change-Id: I338f819f71c18fa9e17015e8a588a3d0207350c6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch replaces all occurences of the macro DEV_FAIL by -EIO
at the driver level. So this patch touch the files under drivers/,
include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I0594ab5dbe667e074c250129e7c13ce512ac940f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
It's not a function and requires all its arguments to be build-time
constants. Make this more obvious to the end user to ease confusion.
Change-Id: I64107cf4d9db9f0e853026ce78e477060570fe6f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename them to DEVICE_NAME_GET and DEVICE_GET to fit in the 'device'
namespace.
Change-Id: I407a7f284ed4d1c071961b46615eea859c2e825f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch introduces the 'QMSI RTC device driver' which is simply a shim
driver based on RTC driver provided by QMSI BSP.
Some config options are independent of the driver implementation used,
so use a consistent name for them. In this case RTC Interrupt number and
Priority use the same config options for both the QMSI and DesignWare
drivers.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_RTC=y
CONFIG_RTC_QMSI=y
Change-Id: I48292406e5472e5786f3b9abbeb71016a273bfec
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Andrzej Głąbek