Add yaml file for initial support of USB PHYs.
It adds also yaml files for STM32 USBPHYC and
USB controllers with embedded PHY.
PHY refers to the physical layer which is used
to connect a device to the physical medium e.g.
USB controller.
Origin: original
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add a dts binding for the Atmel WINC1500 WIFI chip. Update the
quark_se_c1000_devboard to utilize this binding as well as the wifi
sample app.
We now get all the GPIOs related to the Atmel WINC1500 from the device
tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells to the sifive PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F103 micros starting from 64-pin (xE) packages upward have
available port G. This patch defines a dts binding for them.
Signed-off-by: Pavel Kral <pavel.kral@omsquare.com>
Add #pwm-cells to the i.MX PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells to the STM32 PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Newer DTC now warns about mismatch between the reg and unit-address.
Most of these cases are due to case not matching, so fix thoses so
everything is lowercase.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Intel S1000 has 4MB of internal memory.
In DTS it was defined as 3MB and is now updated to 4MB.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
This is found on quark_se_c1000_devboard but can also be wired on
any boad with SPI bus.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add clocks property in stm32l4r5 devices.
Replace i2c2 node by i2c3 node in l4.dtsi as i2c3 available
in all stm32l4 SoCs while i2c2 is not available in some parts.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we have DTS support for an entropy driver we should get the name
generated from DTS ('label' property on the entropy device node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked flash partition extraction so we call it when we see a
node that is 'partiton@' instead of per property. We also handle the
'read-only' property in the flash partition extraction function which
lets us remove 'use-property-label' handling.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells properties to kinetis dts files and update the yaml
binding to spec the two cells as pin and period (in nanosecond to match
Linux Kernel binding spec).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We set 'use-prop-label' incorrectly in the st,stm32-ccm binding file.
This property is meant to generate names based on there being a label
property set in the node. For st,stm32-ccm nodes we don't ever set
labels and the binding file doesn't specify a label. So remove setting
'use-prop-label'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
atmel,sam-watchdog..yaml had the old id field that we have removed.
Remove it so we stop getting a warning about it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add minimal DTS support for the m2gl025_miv. The dts just has the core,
SoC, PLIC, and UART described. We still get memory related info from
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
inventek,eswifi.yaml had the old id field that we have removed. Remove
it so we stop getting a warning about it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove setting of base_label and use-property-label from soc-nv-flash
binding file. We don't really need to set either of these properties
in the binding and it just goes to make things more complicated than
they need to be.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There were several issues in the dts binding for the ssd1673 display:
* binding file mixed description & generation up together
* Use of BASE_LABEL
* orientation-flipped should have been of type boolean
Update the binding file to reflect these changes, and made associated
changes to dts_fixup.h and driver as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A few issues with the dts support for the SSD1306 display driver:
1. binding file mixed description & generation up together
- rename most uses of generation to description and add proper
generation field into yaml
2. Drop use of BASE_LABEL, this shouldn't be used by most bindings
3. dts defines that are being assumed in driver aren't correct. We
should be using a dts_fixup.h in the sample to map the generated
defines to those used in the driver. We remove the incorrect
defines that the driver assumes right now.
4. Fixup 'segment-remap' and 'com-invdir' properties that are booleans
in the binding file and associated code changes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Yannis Damigos