These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in TI CC2650 system initialization code and a few drivers
for this SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Add pin muxing for STM32F302x8 by sharing most of the definitions
of the STM32F303xC. Add USART3 for both the 302x8 and the 303xC.
Add a PWM that is specific to the 302x8.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Group the entries by pin number and then sort them by alternate
function. This helps when editing the file.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The drivers/pinmux/dev directory doesn't containe any CMakeLists.txt
file, preventing to enable the PINMUX_DEV option. Fix that by providing
one.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
ports_enable array holds port clock information.
It is populated for all SoCs, but ports availability depends on
SoCs. The way it is defined today, location of the port in the
array depends on previous ports definition in SoC CMSIS files.
Though, port index is always the same irrespective of previous
ports availability in the SoC.
This will result in incoherency between port index and clock
information.
Fix this by setting a bogus value if port is not defined.
Return an error if bogus value is read.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The STM32F7 uses the same USB OTG FS controller than the STM32F4 series.
It is therefore trivial to add support for it, by adding the DT fixup
and pinmux macros, and the DT entries in stm32f7.dtsi. Keep it disabled,
it should be enabled at the board level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Define the pinmuxing for I2Sx_CK, I2Sx_SD and I2Sx_WS wires (with
'x' in the range 1 to 5). The multiplexing has been selected in
accordance to the ArgonKey board requirements.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The patch adds serial driver support for STM32F7 family
microcontrollers, includes pinmux definitions and DTS fixup file.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The nucleo_f334r8 uses STM32F3_PINMUX_FUNC_PA8_PWM1_CH1 inside its
pinmux but it is not defined anywhere.
Add the definition into the pinmux file to fix the build of
nucleo_f334r8 when enabling CONFIG_PWM.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Enable supporting UART4 on STM32F107 and STM32F103Xe SoCs.
Modified stm32f1/dts.fixup for replacing USART with UART.
Signed-off-by: Jun Li <jun.r.li@intel.com>
There is no pinmux_dw.c and not Kconfig symbols associated with
CONFIG_PINMUX_DW, so remove the references to them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux subsystem does not have any API documenation. Currently
none of the existing pinmux drivers do any kind of input validation
for the pin/op parameters, which has been shown to allow the caller
to access unauthorized memory, up to and including disabling the
MPU.
This requires a proper specification for the pinmux subsystem and
also modification of existingd drivers to validate arguments on a per
driver basis. Remove user mode access until #7390 is resolved.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Andrzej Głąbek