These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added bidirectional I2S support for Intel S1000
- Added implementation for I2S receive mode
- Extended driver instances to support 3 I2S ports
- Added DMA channel mappings for upto 4 I2S ports
- Utilized k_msgq to track buffers through the driver
- Allocate buffers for audio reception in the driver
- Free buffers after audio transmission in the driver
- Perform buffer reload for DMA after every reception/transmission
- Removed unused Kconfig variables
- I2S_CAVS_TX_BLOCK_COUNT
- I2S_CAVS_RX_BLOCK_COUNT
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The dma_tx_callback() function signature is different than the one
required by struct dma_config. So change the signature to fix
a compiler warning.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Align the dma_callback() signature to the new one in order
to avoid warnings during compilation.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
STM32 I2S driver implementation. It has been designed in the most
generic way possible, with the possibility of using it in master/slave
and rx/tx mode. Currenty it has been tested for master rx mode only
using the microphone on ArgonKey board.
The configuration file permits to compile it for STM32F4xx product
family only, but it should be easy to extend it also for other
families.
It supports all 5 STM32F4xx I2S controllers (I2S 1/4/5 on APB2 and
I2S 2/3 on APB1).
It makes uses of the available DMA channels for rx/tx streams.
The clock source can be selected among one of the following two choices:
- PLLI2S pll, with possibility to configure PLLM/PLLN/PLLR
- HSE/HSI clock
Interrupt is triggered only in case of errors (FRM/OVR/UDR).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Remove I2S resource ownership configuration.
Such configuration will be done in an SoC level
initialization routine
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A design flaw of 'gsource' is that there's no way to require at least
one file to match the glob pattern. This could lead to silent errors.
Switch to a new design, where a plain 'source' is globbing and requires
at least one file to match. A separate 'osource' (optional source)
statement is available for cases where it's okay for a pattern (or plain
filename) to not match any files.
'orsource' combines 'osource' and 'rsource' (relative source).
This commit search-replaces 'gsource' with 'source', but backwards
compatibility with 'gsource' is still maintained by making it an alias
for 'osource' (and by making 'grsource' an alias for 'orsource').
The three Kconfig files arch/{nios2,posix,xtensa}/Kconfig source
arch/{nios2,posix,xtensa}/soc/*/Kconfig, which doesn't match any files.
Use 'osource' for those. The soc/*/Kconfig files seem to be for
additional SoC-specific symbols, only none exist yet on those ARCHes.
Also use 'osource' for the source of $ENV_VAR_BOARD_DIR/Kconfig in
boards/Kconfig, which doesn't exist for all boards.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
User mode may now access the read, write, and trigger APIs.
Unlike supervisor mode, memory slabs are not dealt with directly,
the data is always copied.
A new driver API added to fetch the current channel configuration,
used by the system call handlers.
The i2s_sam_ssc driver updated for the new API. CAVS driver not
modified as there is no user mode port to Xtensa yet.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add bit definitions and set M/N divider ownership in
i2s_initialize.
Changes to comply with coding guidelines
Changes to address review comments
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added support for fractional division of reference clock to obtain
I2S bit clocks
For example:
If reference clock is 38.4MHz and
if the I2S format is 2ch, 32bits per channel, 48KHz sample rate,
the bit clock frequency has to be 2*32*48K = 3.072MHz
38.4MHz/3.072MHz = 12.5 (a fraction)
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The driver was using CONFIG_I2S_1_IRQ_PRI which doesn't exist. It
should use CONFIG_I2S_CAVS_1_IRQ_PRI.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Implements the driver for Intel CAVS I2S. Only Playback
is currently supported.
Change-Id: I7b816f9736dc35e79a81d3664d6405dc0aac15b4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Andrzej Głąbek