These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This commit is a fix for Issue #8226
- Error flags are assigned to the correct mailbox now.
- set_filter_mutex is moved from can_stm32_attach to the wrappers
can_stm32_attach_isr and can_stm32_attach_msgq. This protects
response_type variable.
- Waiting for empty mailbox semaphore return value
is checked for none zero values to check all error states.
- The mailbox tx_int_sem is reset before the sending is triggered.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
As part of HAL_CAN_Init we check the initial state of the can handle.
Setting it to HAL_CAN_STATE_RESET as an initial state to start the
Init properly.
Resolves: #8416
Coverity-CID: 186580
Signed-off-by: Sritej Kanakadandi Venkata Rama <sritej.kvr@gmail.com>
This commit splits the common interrupt into rx and tx parts because
only STM32F0 series has a common interrupt.
Moved clock source definition to device-tree.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit moves the bit timing (PROP, BS1, BS2 segments and SWJ)
from Kconfig to the device-tree and fixes issue #7933
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds low level driver support for STM32 micro controllers.
It is tested on stm32f072b in loopback and normal mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Andrzej Głąbek