These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
CONFIG_ADC_DW_REPETITIVE and CONFIG_ADC_DW_DUMMY_CONVERSION aren't
defined anywhere so remove the associated code for these Kconfig
symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
k_poll_signal was being used by both, struct and function. Besides
this being extremely error prone it is also a MISRA-C violation.
Changing the function to contain a verb, since it performs an action
and the struct will be a noun. This pattern must be formalized and
followed and across the project.
MISRA-C rules 5.7 and 5.9
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This just got turned into a function from a "variable" API, but
post-the-most-recent-patch it turns out to be degenerate anyway.
Everyone everywhere should always have been using the kconfig variable
directly, and it was only a weirdness in the tickless API that made it
confusing. Fix.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The existing API defined sys_clock_{hw_cycles,ticks}_per_sec as simple
"variables" to be shared, except that they were only real storage in
certain modes (the HPET driver, basically) and everywhere else they
were a build constant.
Properly, these should be an API defined by the timer driver (who
controls those rates) and consumed by the clock subsystem. So give
them function syntax as a stepping stone to get there.
Note that this also removes the deprecated variable
_sys_clock_us_per_tick rather than give it the same treatment.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Replaces direct accesses to the peripheral registers structure
with the proper SAADC HAL function that appeared recently in nrfx.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The interval_us is supported by the adc_context code. It is not a
feature that the driver writer needs to code to support. Fixes
bug #9723.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Major rework of the mcux adc16 driver to convert it to the new adc api.
Currently supports a subset of the api features including synchronous
and asynchronous reads, and consecutive reads triggered by the kernel
timer.
Does not yet support some of the channel configuration options such as
gain and reference voltage because the hardware only allows these
options to be configured by peripheral instance rather than by channel.
The values are currently hardcoded in the driver, but in the future we
could introduce some flexibility per instance via device tree
attributes.
Does not yet support consecutive reads triggered by a hardware timer.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit adds translation layers to make nrfx drivers for the nRF
ADC (nRF51 series) and SAADC (nRF52 series) peripherals accessible via
the Zephyr's API. The SAADC peripheral is accessed using nrfx HAL only
as it turns out that usage of the nrfx driver in this case would be
inconvenient and would unnecessarily complicate the shim.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit replaces the API for ADC drivers with a reworked one.
As requested in the issue #3980, the adc_enable/adc_disable functions
are removed. Additionaly, some new features are introduced, like:
- asynchronous calls
- configuration of channels
- multi-channel sampling
Common parts of code that are supposed to appear in each implementation
of the driver (like locking, synchronization, triggering of consecutive
samplings) are provided in the "adc_context.h" file to keep consistency
with the SPI driver. Syscalls are no longer present in the API because
the functions starting read requests cannot use them, since they can be
provided with a callback that is executed in the ISR context, and there
is no point in supporting syscalls only for the channels configuration.
"adc_api" test is updated and extended with additional test cases,
with intention to show how the API is supposed to be used.
"adc_simple" test is removed as it does not seem to add much value.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The toplevel adc_seq_table is now copied onto the stack and
the stack copy used.
The contained entries array is now copied onto an allocation
drawn from the caller's resource pool, to prevent modification
of the buffer pointers.
The return value policy here is to oops the caller if bad memory
or objects are passed in, but return an error otherwise.
Based on an original patch by Leandro Pereira, rebased and the
copy of the entries array added.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
TI's ADC108S102 is a sampling on 16 bits, and thus requires the
destination buffer to be made of an even number of bytes.
Fixes#7389
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
num_entries can be as large as 255. However, based on the
_ti_adc108s102 implementation, num_entries must be less than
ADC108S102_CMD_BUFFER_SIZE or the cmd_buffer[] and
sampling_buffer[] arrays in the data struct could overflow.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Channel IDs start at 0, need to fail if the provided ID
equals ADC108S102_CHANNELS, not just larger than it.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Straightforward conversion for adc_enable/disable.
adc_read() uses a sequence table, which points to an array
of struct adc_seq_entry, each element pointing
to memory buffers. Need to validate all of these as being readable
by the caller, and the buffers writable.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
SoCs outside the Kinetis family can have the ADC16 module, so move the
HAS_ADC16 config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds common and Kinetis-specific adc device tree properties, and updates
all Kinetis SoC and board dts files to include adc nodes.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Kconfig assumed that there would only ever be one instance of an
adc, but some Kinetis devices have multiple adc instances.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Andrzej Głąbek