Some of the Panasonic's evaluation boards have limited amount of pins.
So not all arduino pins can be occupied and not all shields are
compatible.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
In order to bring consistency in-tree, migrate all samples to the use
the new prefix <zephyr/...>. Note that the conversion has been scripted:
```python
from pathlib import Path
import re
EXTENSIONS = ("c", "h", "cpp", "rst")
for p in Path(".").glob("samples/**/*"):
if not p.is_file() or p.suffix and p.suffix[1:] not in EXTENSIONS:
continue
content = ""
with open(p) as f:
for line in f:
m = re.match(r"^(.*)#include <(.*)>(.*)$", line)
if (m and
not m.group(2).startswith("zephyr/") and
(Path(".") / "include" / "zephyr" / m.group(2)).exists()):
content += (
m.group(1) +
"#include <zephyr/" + m.group(2) +">" +
m.group(3) + "\n"
)
else:
content += line
with open(p, "w") as f:
f.write(content)
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit adds const modifier in second argument for
sensor trigger handler.
There is no reason to modify this data and this change
would allow to store trigger configuration also in FLASH.
Fixes: #38929
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Rename the NXP LPCXpresso55S16 board definition from
lpcxpresso55s16_ns (non-secure) to lpcxpresso55s16 and remove TF-M
configuration options.
While the LPC55S16 does have Arm TrustZone support, there is no TF-M
support available upstream yet.
Fixes#35100
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Shield x_nucleo_iks01a3 could be used with board stm32mp157c_dk2,
but it requires not using the irq-gpio pin.
Provide a specific configuration for this board that does not make
use of this pin, sot set all sensors' triggers mode to NONE.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
By default, prj.conf is the CONF_FILE file use by any application.
Use the file when it is not the case and remove the line that sets
it in CMakeLists.txt as this is not required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Samples that include floating-point format specifications may need
cbprintf FP support. Make sure it's available.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Exclude the NXP LPCXpresso55S16 board from the X-NUCLEO-IKS0xAx
samples, since the rely on having Arduino Uno header A3 available.
On the LPCXpresso55S16, A3 is connected through a resistor (R63) which
is not mounted by default.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This provides a better error message when building with CMake and
forgetting ZEPHYR_BASE or not registering Zephyr in the CMake package
registry. See parent commit for more details (split from parent for
better readability).
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
After running command --list-test-duplicates
I found out that some test cases have same names (duplicated).
To get rid of it, I decided to change names in .yaml files
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. If you reset the x_nucleo_shield3 board
the LSM6DSO enter in hot join, as INT1 '1' level is preserved by
the level shifter.
This commit switch to INT2 to generate DRDY interrupt, so that INT1
always remain to logical '0' level.
Fixes: #20933
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DTSpec writes this as a single word, presumably to make it easier to
grep for / more precise. Follow along in the rest of the docs now that
our main DT docs page agrees with this usage.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Add support to LIS2MDL trigger, dynamic odr configuration as well as
temperature data reading.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LIS2MDL is not a combo device, but pure magnotemeter.
Hence, '-magn' extension is not adding information and can
be removed from dts compatible name as well as binding filename.
Instead specify '-i2c' or '-spi' to distinguish between the names.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update a number of boards that have arduino_gpio and arduino_i2c
support in their dts files to show that they support that in the
board.yaml file. This allows coverage on several shield tests that
utilize the tags 'arduino_gpio' and 'arduino_i2c'.
Exlucde stm32mp157c_dk2 from some of the samples right now since the
connector on the board doesn't support A2/A3. Also remove the duplicate
of exluding disco_l475_iot1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change arduino_header depend to arduino_gpio as that is more meaningful.
Its easy to mistake arduino_header to mean the board has an arduino
header in general. What we want to depend on is that we have the gpio
connector in the dts that has 'arduino_header' as the node label.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide two basic example samples to test the x-nucleo-iks01a3 shield:
- Standard (Mode 1)
- SensorHub (Mode 2)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Steffen Jahnke