Added a new UART driver for posix arch boards.
The driver can be configured to either attach to a new
pseudo-terminal, or to connect to the invoking shell
stdin-out.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added basic PSoC6 UART driver and added two UART nodes in the PSoC6
device tree to have output from CM0+ and CM4 cores.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
1. Added support for two instances of UARTE.
2. Kconfig.nrfx is capable to configure UART and UARTE driver.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This commit adds support for Microsemi Mi-V RISC-V softcore CPU
running on the M2GL025 IGLOO2 FPGA development board.
signed-off-by: Karol Gugala <kgugala@antmicro.com>
UART driver renamed to keep the same convention as SPI and TWI drivers.
All substrings: "UART_NRF5" in defines renamed to "UART_NRFX_UART".
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Adds a shim layer around the imx uart driver to adapt it to the Zephyr
serial interface.
Modem mode was introduce to control it as DCE and DTE and can be
configured in the device tree:
modem-mode:
type: int
category: required
description: Set the UART Port to modem mode 0 (dce) 1 (dte)
generation: define
For now only the UART 2 was tested.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Add usart-yaml in dts.
Build fsl_lpc_usart and fsl_lpc_flexcomm in
ext/hal/nxp/mcux/drivers/Makefile.
Only polling mode is implemented in usart now. Interrupt can be added in
future.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The CMakeLists lost the config for uart_mcux_lpsci.c, which is the
console driver for board frdm_kl25z. So just add "uart_mcux_lpsci.c"
into drivers/serial/CMakeLists.txt to make it work.
Signed-off-by: Jason Wang <jason.yanping.wang@hotmail.com>
Delete the native UART JTAG driver as we will be reusing
the Altera's HAL driver.
Add the shim driver support for Altera HAL's JTAG UART soft IP.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Anas Nashif