pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
This patch populates "clocks" property in stm32 usb nodes
for clock related usb configuration code of each dtsi files
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add flash support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch adds support for the STM32G071xx
from STMicroelectronics.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Protect gpio_configure function in dual core context.
This operation is not needed for other fuctions of the api:
* init
* read
* write
Protecting gpio_configure also protects access to
interrupt_controller IP.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for C-M4 core on STM32H7 series.
It is enabled in Dual core context with 2 alternatives boot methods:
* Boot CM4 CM7: Both core boot at reset, then CM4 enters Stop mode.
CM7 performs system configuration then finally wakes up CM4
* Boot CM7, CM4 Gated: Only CM7 boots at reset. Once done with
system configuration it triggers (requires option byte update)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide basic clock control driver for STM32H7.
Bus clock activation is done through CM7 and CM4 common registers
so we don't have to care to the CPU Id before accessing.
Accesses are not protected for now. Only possible configuration
is system clock source set to HSE driven PLL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
UART related defines in STM32F7 files where filled with
references to USART.
Instances 4, 5, 7 and 8 of SoC serial port are actually UARTs.
So rename define's accordingly. Otherwise it couldn't build.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Definition of obsolete FLASH_PAGE_SIZE Kconfig symbol was
remaining in STM32F3 soc files.
Clean these.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
stm32mp1 was adding a STM32 specific Core selection Kconfig
symbol while zephyr generic CPU_CORTEX_M4 could be used for the
same purpose.
Remove STM32 specific symbol and use generic one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In kernel_arch_init() we initialize the ARM core (interrupt
setup, fault init, etc.) so we can also move z_clearfaults()
in the same function and skip invoking it in the SoC init
functions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Hex firmware file is convenient in some scenarios, like
generating signed firmware with `west sign`. So, enable
generating hex file.
Signed-off-by: Jun Li <jun.r.li@intel.com>
This commit adds driver support for ADC1 on all 8 supported series of
stm32 with resolution and conversion time selection and calibration.
Currently DMA is not supported for all series, and without it, zephyr
won't be able to catch up ADC's end of conversion interrupt, so this
version of the driver supports one channel conversion only. Users want
multi-channel conversion should use multiple sequences in their app
code.
This driver uses LL lib rather than HAL because the current HAL lib for
ADC will call HAL_DMA_* functions rather than using zephyr's common DMA
interface, so that way the driver will break the consistency of the
code.
This driver has been tested on multiple nucleo boards including
NUCLEO_F091RC/F103RB/F207ZG/F302R8/F401RE/F746ZG/L073RZ/L476RG and all
passed the test cases in tests/drivers/adc/adc_api. If the external ADC
line is floating, it may fail the tests since ADC may get 0V and the
test cases think 0 is failing. Connect it to any voltage source between
0-3.3V will help passing the test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Markus Fuchs