Replace specific STM32F1 references with generic STM32 ones.
Use generic names like U(S)ARTx for instances which have different
naming across STM32 families.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
A previous commit had mistakenly overwritten the copyright years instead
of extending the range. Fix this mistake so that the proper range is
recorded.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The existing nrf5_common.h now applies to other Nordic ICs that are not
part of the "5" family. Instead rename this to nrf_common.h to cover the
upcoming ICs that belong to other families.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
There are some minor differences between the UART om SAMD20 and SAMD21
that we need to take into account:
SYNCBUSY bit for the samd20 is located in the STATUS reg.
The samd20 does not have a SAMPR bit like the samd21.
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The nrf52840 has 2 gpio ports, and 48 GPIO. We need to
adapt the range to allow the gpio on port 1 to be used
by this driver
Signed-off-by: Giuliano Franchetto <giuliano.franchetto@intellinium.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Add usart-yaml in dts.
Build fsl_lpc_usart and fsl_lpc_flexcomm in
ext/hal/nxp/mcux/drivers/Makefile.
Only polling mode is implemented in usart now. Interrupt can be added in
future.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The CMakeLists lost the config for uart_mcux_lpsci.c, which is the
console driver for board frdm_kl25z. So just add "uart_mcux_lpsci.c"
into drivers/serial/CMakeLists.txt to make it work.
Signed-off-by: Jason Wang <jason.yanping.wang@hotmail.com>
STM32 UART driver uses a macro for clock initialization, that
is difficult to read and incompatible with needed changes to
fix STM32F0 series UART problems.
This change switches to using the full clock bus names in UART
init functions removing the macro-magic and increasing
readability.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Fix#5298
irq_is_pending function returned TXE/RXNE flag status
even if IRQ was masked, which led to enless loop
in uart_pipe when no TX was performed. Fix by reporting status only when
IRQ is unmasked.
Signed-Off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In uart_nrf5.c the IRQ masks for the TX READY and ERROR events are
incorrect. This pull request fixes the mask values so they are
according to the nRF51/nRF52832/nRF52840 product specification.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Delete the native UART JTAG driver as we will be reusing
the Altera's HAL driver.
Add the shim driver support for Altera HAL's JTAG UART soft IP.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Certain interrupt-driven APIs were excluded as they are intended
only to be called from ISRs, or involve registering a callback
which runs in interrupt context.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Refactors the mcux lpsci shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use the clock control interface instead of calling CLOCK_GetFreq()
directly. This will allow SoCs with different clock architectures to
reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds support for on board UART_0 on MSP-EXP432P401R-LAUNCHXL.
Driver makes use of driverlib available in ROM by default, thus saving
code space.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Also provide their prototypes in `soc.h`. This should help
readability, since some ROM functions, with their names as provided by
Espressif, have sometimes the same prefix as Zephyr APIs.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
TEMT is Transmitter Empty bit which is set only when the full FIFO
is empty. It makes sense to poll for THRE (Transmitter Holding
Register Empty) which is set when UART can buffer new character
for transmission (there is room in FIFO). This allows using the
FIFO in full.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The LCR register specifies the format of the asynchronous data
communication exchange. Keep the data/stop bit and parity settings
intact during baud rate change.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
When transmitting to the UART interface using polled mode, the ESP32
driver would return 0 regardless of the success state. Return the
character that has been transmitted to comply with the API.
Jira: ZEP-2552
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Esp-idf defines the BIT macro that is also defined in Zephyr's
misc/util.h. Fix the issue by including the esp-idf headers first, so
that a check in util.h won't redefine the macro if it's already
defined.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The ESP32 UART driver can only be used on the ESP32 SoC AFAICT. But it
did not have a depend clause so it was polluting the options of other
platforms.
With this patch the ESP32 driver will no longer be exposed to users of
non-ESP32 devices.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Ilya Tagunov