Update RT5xx and RT6xx clock init to add the code
to set the I3C dividers. This code has been moved
from the I3C driver.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Reverts bus clock settings. Follows MCUXpresso SDK clock settings, and
sets to output of SysPLL2 PFD3 at 198 MHz.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
Timer/PWM Module (TPM) initial clock source is not selected.
Add initial clock source selection based on Devicetree configuration.
Rename clock sources definitions from LPUART specific to general names
usable by several modules on the SoC.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Fix USB w/ SPEED_OPTIMIZATIONS for LPC55xxx SoCs
Root cause was non-volatile register access,
which could get optimized by the compiler
(by -fschedule-insns, specifically)
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Imply CONFIG_INIT_AUDIO_PLL on nxp,dmic driver selection on
mimxrt685s/cm33. Make DMIC clock config dependent on the use of the
RT685's audio PLL.
Fixes a regression described in #77851.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Generic hook infrastrucutre was added to Zephyr, but NXP MCXC SoCs
were not updated accordingly.
Use generic hook infrastrucutre for MCXC SoCs.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
The i.MX95 applications processor features advanced graphics and
video cores, powerful vision and machine learning acceleration,
efficient CPU performance, real-time processing, and advanced
security with the integrated EdgeLock® secure enclave to support
energy-efficient edge computing.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The custom linker script was required because SOF needed
some extra linker sections. Other than that, the custom linker
script was identical to the common architecture script. This
commit removes the custom linker script because:
* keeping the custom linker script in sync with the
common one is troublesome.
* application-specific linker sections shouldn't be
included in the generic soc linker script. Instead,
they should be handled at the application level
(i.e: via cmake commands if additional sections are
needed or via a new, custom linker script if more
changes are needed)
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Fix flexspi xip configuration issue regarding code relocation
due to the order of kconfig defaults being sourced
The flexspi setup was not being relocated to an on chip location
Also remove rt1060 conf file in flash common test which changes the
code relocation location to RAM, just keep as ITCM for all M7 which
as of now all have ITCM from NXP with flexspi.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Use generic hook infrastrucutre instead of custom Kconfig and hooks for
ARM.
Replace z_arm_platform_init() with platform_reset().
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Include compile of the flash file when FlexSPI_XIP is enabled
even when the FlexSPI driver is not enabled.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
RT1011 expects it's flash configuration block at a different offset than
the rest of the RT10xx series. Add default to fix the platform not
booting.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add clock config for Flexcomm peripherals functioning as I2S interfaces.
Add MCLK clock config for the WM8904 codec located on the mimxrt595_evk
and mimxrt685_evk boards.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Enable DMIC clock in soc.c - attach to chip's audio PLL. Add pinmux
definitions for the DMIC peripheral. Add nodes to SoC's device tree for
the DMIC peripheral and its audio channels. Configure the DMIC
peripheral in board's device tree to enable audio capture.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
dts: arm: nxp: mimxrt1180_evk: add GPT1/2 instance into devicetree
Enable GPT1/2 clock
Add GPT1/GPT2 instances
Set GPT2 as a counter, the default frequency is 240000000
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
FCB was being relocated to the wrong location, and the flexspi clock
setup was not being relocated.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
IMXRT11XX secondary core should not deinit ENET PLL
as it could be configured by primary core.
Signed-off-by: Anders Bjørn Nedergaard <abn@polytech.com>
Move default of monolithic and fw loader, options, etc to the
common kconfig files rather than defaulting in soc file.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Consolidate the ROM RAMLOADER config to be in one place,
add a new Kconfig file to be included by the SOCs with the feature.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The CONFIG_USB_MCUX_CONTROLLER_TYPE choice config
is not necessary, let's just remove it. Theoretically,
if there was an SOC with the EHCI and LPCIP3511, then
it might cause a build error, but there is no SOC
which is supported on this legacy driver that has that.
Remove all settings of it in the SOC files.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Currently this code related to how to configure the
flash size and address when using flexspi to XIP is copy
pasted in all sort of places and ways all over the tree,
let's clean this up and have single point of control over
this configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move all dependencies of the family config to series level,
and put a disclaimer saying not to use the family config.
Change all occurrences of the family config in code to the
MCXNX4X series config.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
NXP is not supporting these derivative parts in the zephyr upstream,
these references to them should therefore be removed in order to avoid
confusion.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The Kconfig defaults should be in Kconfig.defconfig.
MFD should not be made dependent on the LP flexcomm being
enabled, since MFD can be for other things than just flexcomm.
Change from depends on to an if.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Doesn't seem like there is any reason to be changing the
serial and ADC driver init priorities in the SOC defconfigs.
By default, clock control has priority 30, dma has priority 40,
and serial/adc have priority 50. This seems already to be the order
that is needed, and the original goal of these overrides, which
don't seem necessary anymore.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
There are some SOCs which use the same pinctrl
device, but are not really overall that similar to the kinetis
family of SOCs, so prepare to reuse this code by other SOC families.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Mahesh Mahadevan