Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Adds common and Kinetis-specific adc device tree properties, and updates
all Kinetis SoC and board dts files to include adc nodes.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
patch adds zephyr,uart-pipe to devie tree as chosen property.
This is added for frdmk64f because sanitycheck test was
breaking with changes of generating configs for UART_PIPE
from device tree instead of Kconfig.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
A number of sectors are declared in the frdm_k64f flash partitions
node as part of an "application state" partition. Rather than require
users to treat this area of flash as a single partition, delete the
application-state node and leave a comment in its place describing its
purpose.
This enables use cases where the flash sectors must be split into
multiple partitions without defining overlapping partitions in overlay
files.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Currently, flash partitions used by mcuboot are defined in the
SoC-level dtsi file for NXP K6X. This should be made more granular so
that product owners can choose partition layouts to suit their
needs. To that end, move the partitions into frdm_k64f.dts.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The I2C controller nodes are the root of the I2C bus for that controller
and thus may have children nodes that represent the I2C devices on that
controller. Thus we need to specify the #address-cell & #size-cell
properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
+ The VBLUno52 board
nRF52832 ARM Cortex-M4F processor
Bluetooth Low Energy 5.0
DAPLink interface
UNO pinout
4 power
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since we support uart0 on the cc2650 sensortag we should have a
reference for zephyr,console in chosen for it. This will be useful as
we start to generate Kconfig defines based on zephyr,console.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The SAM4S, SAM3X, SAME70 all use the uart_sam.c serial
driver. This patch puts the configuration in DTS and
out of Kconfig. The SAME70 uses the USART as well.
USART DTS support for the SAME70 is also in this patch.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
+ VBLUno51 board
nRF51822
Bluetooth Low Energy
DAPLink interface
UNO pinout
4 power
+ Wiki: https://vngiotlab.github.io/vbluno/
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
With this partition: mcuboot up to 64KB, user app up to 432KB, an
application state of 64KB, and a swap sector of 24KB.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
Renames k64sim to nxp,k64f-sim to be more consistent with other files.
The sim hardware can vary across Kinetis SoCs, so this dts is not made
to be generic.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Multiple Kinetis SoCs have the same gpio hardware as the k64 and can use
the same mcux driver, so rename the dts to be more generic.
Also fixes some stranded references to kw41z-gpio to the new
kinetis-gpio.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Multiple Kinetis SoCs have the same pinmux hardware as the k64 and can
use the same mcux driver, so rename the dts to be more generic.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Multiple Kinetis SoCs have the same lpuart hardware as the kw41z and can
use the same mcux driver, so rename the dts to be more generic.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Multiple Kinetis SoCs have the same uart hardware as the k64 and can use
the same mcux driver, so rename the dts to be more generic.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
The Sam4x HAL defines __NVIC_PRIO_BITS to 4. Fixes an issue where
interrupt priorities and masking were not being done correctly.
Issue: ZEP-2243
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update driver to use DTS-generated #defines for port names,
and not obsolete Kconfig variables.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Recent changes (69255043, 91f67a13, 84628e8b, fa4a3932) add support
for a partition table in the flash. Add support for this to the nxp
k6x dtsi file. By default, code will occupy the entire flash. By
setting a chosen node in an application, the code can be linked into
one of the partitions. For example, and app could create a
'frdm_k64f.overlay' file at the top of their project with:
/ {
chosen {
zephyr,code-partition = &slot0_partition;
};
};
to place an application in slot 0.
Signed-off-by: David Brown <david.brown@linaro.org>
- board name olimex_stm32_e407
- CPU STM32F407ZGT6 Cortex M4
- LED/BUTTON support
- Console on USART1 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The Sam3x HAL defines __NVIC_PRIO_BITS to 4.
Fixes an issue where interrupt priorities and masking
were not being done correctly.
Issue: ZEP-2243
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This commit rework stm32f4 series dtsi files hierarchy.
stm32f4.dtsi was used as maximum common set of IP while it should
be considered as the minimum common subset.
Then, following on stm32f4 series hierarchy and inheritance rules,
stm32f4xxx.dtsi files are reworked to include the "parent" soc dtsi
file and then add own IPs to each SoC.
Change-Id: I394278c84a8ea38921f9f143f4fc52ef1c645d05
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In stm32 dtsi linux files, uart generic node name is serial.
Rename uart node names of stm32 dtsi files from uart@ to serial@
Change-Id: Iac5cbf7955f23cee520bc1790b0f324a17bfcf9e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes uart only nodes situation for stm32 devices.
st,stm32-uart yaml description is added to enable compilation
Change-Id: Iea78693bdfb90fbb09612b75685ed7ca0ccca6d6
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The chosen property that sets which serial port is being used for the
console device wasn't set. Add the property "zephyr,console" to the
Arduino Due, CC3200-LaunchXL, CC3220SF-LaunchXL, and QEMU Cortex M3
boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the Atmel SAM3 UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kumar Gala