The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Comment for storage partition could be misleading.
Clarify this is a partition used for file system.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds DT description of generic storage flash partition using
the last 16kB of flash when CONFIG_FS_FLASH_STORAGE_PARTITION is
defined. This can be used for FCB or NVS filesystems.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The ST Nucleo L432KC board only has a reset switch and not user switch.
It has a single user LED connected to PB3, and called LD3 in the ST
documentation.
This patch fixes the corresponding device tree definition. At the same
time also it also fixes the documentation, where the name of the power
and user LEDs are swapped.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure SPI using DT for the following STM32 boards:
96b_neonkey
nucleo_f091rc
nucleo_f334r8
nucleo_f401re
nucleo_l432kc
nucleo_l476rg
SPI nodes in <board>.dts file are populated matching boards existing
pinmux default configuration and enabled in Kconfig.defconfig if
SPI is enabled.
For nucleo_l476rg board SPI2 and SPI3 nodes are not yet added, because
of missing pinmux defines.
Fixes#5836
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Ulf Magnusson