Having a per-instance init function makes code cluttered and hard to
read. Just create a per-instance IRQ connect function (required to
resolve IRQ_CONNECT parameters at compile time).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using NRFX_SPI(S|M)_INSTANCE helper so that peripheral address from
Devicetree is used. We should not rely on HAL for hardware description
but Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The maximum transfer chunk length is SoC specific, not instance
specific. This patch defines MAX_CHUNK_LEN at driver level in a SoC
specific manner instead of using HAL values that are instance specific
but that always take the same value depending on the SoC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit aligns SPIM shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Extend the macro with checks for DT properties related to pin
assignments that are defined but would be ignored, depending on
whether PINCTRL is enabled or not, what presumably indicates
a resulting configuration different from what the user expects.
Add also a possibility to indicate that the pinctrl-1 property
should not be checked because the caller does not support the
sleep state.
Rename the macro so that its name better reflects its function.
Update accordingly all drivers that use it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the SPI drivers that handle
the nRF SPI, SPIM, and SPIS peripherals. Update code of the drivers
and related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
- clean up registration of the drivers with the logging subsystem
- use consistent naming of local variables accessing configuration
and runtime data of driver instances, for easier code maintenance
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Only run the `uninit` function if the SPI instance has previously been
configured. This stops an assertion in the HAL drivers from triggering
due to running `uninit` without a previous `init`.
Fixes#42299.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This is a follow-up to commits 99daca9bba
and ae03c0a6bf.
nRF SPI driver shims cannot use devicetree instance indexes, they need
to use the DT_NODELABEL macro and SoC peripheral instance indexes.
Correct the macros used in initialization of CS GPIOs in those shims.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In case when we have multiple devices connected to the
one SPI interface the initial state of CS gpios after
MCU reset is floating and it might be low that prevents us from
communicating between particular devices. Fix that by
initializing all provided cs gpios and setting them as inactive.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to the nRF5340 PS, for 32 Mbps high-speed SPI using SPIM4,
drive configuration H0H1 must be used. The underlying nrfx_spim driver
does it properly in its initialization function, so change the shim to
(re)initialize the driver when the SPI configuration is to be changed
(only then the speed to use is known), to avoid the need of duplicating
the corresponding code in the shim itself.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
According to the nRF5340 PS, SPIM4 only supports 32 Mbps when
the application core is running at 128 MHz. This patch adds
the corresponding check.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to the documentation the OFF state has to be used when the
devices is fully turned off, ie, power removed. Most drivers were using
a sort of fall-through for all non-active states, leading to behaviors
not following the specifications.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The verb tense for the suspended state was not consistent with other
states. The likely reason: state was being used as a command/action.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The difference between low power and suspend states is a thin blur line
that is is not clear and most drivers have used indistinctly. This patch
converges to the usage of the suspend state for low power, since
contrary to the low power state, it is used by both system and runtime
device PM. The low power state is still kept, but its future is unclear
and needs some discussion.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move all PM_DEVICE_STATE_* definitions to an enum. The
PM_DEVICE_STATE_SET and PM_DEVICE_STATE_GET definitions have been kept
out of the enum since they do not represent any state. However, their
name has not been changed since they will be removed soon.
All drivers and tests have been adjusted accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Limit the maximum SPI frequency to that supported by the instance
hardware. This stops peripherals supporting >8MHz on slow instances
from wrapping around on the clock frequency for undefined behaviour.
Fixes#34402
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the devicetree node as the source of object name and other
information used when defining the device structure.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Keep locking for SPI_LOCK_ON from the first call of transceive until
spi_release release the lock. Use owner parameter to in the spi_context
to store the owner of the lock.
The locking is in line with the SPI_HOLD_ON_CS
Signed-off-by: Stefan Bigler <stefan@bigler.io>
This removes a semaphore unlock in init_spi function
which causes risks of competitive access
Signed-off-by: Clotilde Sattler <clotilde.sattler@stimio.fr>
Gerard Marull-Paretas