* Utilize DT_HAS_<COMPAT>_ENABLED for devicetree based drivers
* Move to using 'select I2C'/'select I2S' instead of 'depends on'
(see commit df81fef944 for
more details)
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of selecting appropriate HAS_HW_NRF_* options for particular
nRF SoCs (and simulated nRF52 target), set their values basing on
information from devicetree.
Correct also semantics of those options so that they are set only when
a corresponding DT node is enabled. This allows using them directly in
Kconfig dependencies of Zephyr drivers for nRF peripherals. Update
appropriately these dependencies.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Extend the macro with checks for DT properties related to pin
assignments that are defined but would be ignored, depending on
whether PINCTRL is enabled or not, what presumably indicates
a resulting configuration different from what the user expects.
Add also a possibility to indicate that the pinctrl-1 property
should not be checked because the caller does not support the
sleep state.
Rename the macro so that its name better reflects its function.
Update accordingly all drivers that use it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the DMIC driver that handles
the nRF PDM peripheral. Update code of the driver and the related
devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Shims for nrfx drivers should only connect the related IRQ handlers,
they should not enable the IRQs, as this could lead to a situation
where the interrupt handler is called before the driver had a chance
to properly initialize the peripheral and install the provided event
handler. nrfx drivers will enable the interrupts appropriately on
their own by calling the NRFX_IRQ_ENABLE macro which is implemented
in nrfx_glue.h as a call to irq_enable().
This commit fixes the above issue spotted in the following shims:
- dmic_nrfx_pdm
- clock_control_nrf
- i2s_nrfx
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The device configuration field access was dropping const qualifier for
no reason, don't do that.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use struct i2c_dt_spec to simplify code. This change also allows to drop
device_get_binding usage.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The bus device can be obtained at compile time, so use DEVICE_DT_GET
instead. Device configuration is now used to store the bus device
reference.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a shim that allows using the nrfx PDM driver via the Zephyr API.
Add also missing devicetree nodes representing the PDM peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-pdm" binding with a new property that allows
specifying the clock source to be used by the PDM peripheral (so that
it is possible to use HFXO for better accuracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The AUDIO_DMIC INIT_PRIORITY definition is set to 60 by default,
but this value is causing dmic drivers to be initialized prior to
i2s, to which they are dependent from.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Port the I2S and DMIC drivers to the new timeout API so that they do
not need to enable legacy timeouts.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
As a precursor to the new GPIO API in which GPIO_DIR_OUT isn't a dts
flag move setting of GPIO_DIR_OUT from the dts to explicitly in the
code. We remove setting the flag in intel_s1000_crb.dts as part of this
cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Consistently place C++ use of extern "C" after all include directives,
within the negative branch of _ASMLANGUAGE if used.
Only updated in headers that already had support for drivers built with
a C++ compiler.
The spi_dw.h file defines macros to declare functions, then uses them
within a file that may have out-of-tree overrides. In this case we
leave the including file extern "C" active for backward compatibility.
Background from issue #17997:
Declarations that use C linkage should be placed within extern "C"
so the language linkage is correct when the header is included by
a C++ compiler.
Similarly #include directives should be outside the extern "C" to
ensure the language-specific default linkage is applied to any
declarations provided by the included header.
See: https://en.cppreference.com/w/cpp/language/language_linkage
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2s.h to drivers/i2s.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move dma.h to drivers/dma.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In stereo case the pdm stream continuosly alternates 1-bit from
the left channel with 1-bit from the right channel. In this case
we need first to demultiplex channels bits on byte basis.
Then the Open_PDM_Filter library has to be called twice, one for
each channel.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These files are 'source'd within an 'if AUDIO_DMIC', in
drivers/audio/Kconfig.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. Dependencies on menus work similarly. There are no
"conditional includes" in Kconfig, so 'if FOO' has no special meaning
around a source. Conditional includes wouldn't be possible, because an
if condition could include (directly or indirectly) forward references
to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Kumar Gala