Add defines for radio timer capture and compare indices used
in the nRF Radio HAL implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Removes support for B0 revision silicon. The B0 revision is no longer
recommended for use in host-controlled applications and there are no
users of this driver implementing B0 silicon in their final design.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Adds support for the control port write-lock feature introduced in
revision B1. The write-lock feature minimizes the risk of spurious
I2C writes flipping sensitive bits during device operation by blocking
writes to some or all of the register map.
If desired, the write-lock must be set in hardware by biasing PGPIO2
appropriately and setting the cirrus,hw-i2c-lock flag in the devicetree
entry.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Documents cirrus,hw-i2c-lock property in the devicetree bindings. This
flag indicates that the control port write-lock was enabled in hardware
via the PGPIO2 pin.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Adds support for revision B1 silicon when checking CHIP_REV. This
silicon revision introduces the hardware I2C lock.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Moves the CHIP_REV log message after the CHIP_REV switch case. Printing
the log message after allows for the print to be reused for multiple
CHIP_REV cases.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Use FIELD_GET macro to grab CHIP_REV bitfield. This change improves
the readability of the source code and does not change functionality.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
In case of multiple OSes running on different CPU Cores which share the
same GIC controller, need to avoid the distributor re-configured to avoid
crash the OS has already been started.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add a pinctrl driver for Microchip MEC5 HAL based chips.
The driver removes the YAML enum "no change" property
value from the driver strength and slew rate properties.
Update the shared header file in mec soc common folder to
use a different Z_PINCTRL_STATE_PINCFG_INIT for MEC5.
Modifications to legacy MEC172x XEC PINCTRL will be in
a future PR.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
CMSIS SystemInit is not used in Zephyr. Implement the functionality
that isn't already done by Zephyr startup using soc_prep_hook().
The reason the lack of TrustZone init did not create immediately obvious
issues previously is that SMU faults can only happen if the SMU clock is
enabled.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
For easier recognition PHYTEC boards have been prefixed with the SoC name.
As the new hardware model includes the SoC and cpu, this prefixing is not
needed anymore. All PHYTEC eval boards have an individual and unique name
and can be found easily via this name.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
For easier recognition PHYTEC boards have been prefixed with the SoC name.
As the new hardware model includes the SoC and cpu, this prefixing is not
needed anymore. All PHYTEC eval boards have an individual and unique name
and can be found easily via this name.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
The CONFIG_DUMMY_DISPLAY is now enabled in conjunction with devicetree,
So, no need to be explicitly enabled.
Remove the setting.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The CONFIG_DUMMY_DISPLAY is now enabled in conjunction with devicetree,
So, no need to be explicitly enabled.
Remove the setting.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
As per dma_stop() documentation, the implementation has to not just stop
the transfer, but also to disable the channel. Before this commit, only
the transfer has been stopped.
Same goes for dma_start(). This also allows the enabling of a channel to
be removed from dma_si32_config().
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Replace OVERLAY_CONFIG with CONF_FILE since no-device-pm.conf
contains an alternative configuration to the one in prj.conf
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Replace OVERLAY_CONFIG with CONF_FILE since the file in question
contains an alternative configuration to the one in prj.conf
as clearly stated in the sample doc
'If you use poll you should also use `prj_poll.conf` instead of
`prj.conf`.'
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Move stm32_blk.conf ouside of 'boards' as this folder is meant to
contain only board-specific devicetree overlays and Kconfig fragments.
Signed-off-by: Abderrahmane Jarmouni <git@jarmouni.me>
Fixes: #80200
CMake `find_package(<package> <version>)` support the use of ranges,
like `1.0.0...4.0.0`.
Update the FindZephyr-sdk.cmake module to support this.
This allows looking up the Zephyr SDK with an upper boundry, for example
`find_package(Zephyr-sdk 0.16...<0.17)`.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Die temperature polling sample is not enabled for frdm_mcxc242 board.
Add devicetree overlay and Kconfig configuration for the sample to
enable it.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Remove Kconfig dependency on SOC_FAMILY_KINETIS as the temperature
sensor is available also on MCX family.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Die temperature measurement is not configured in devicetree
for NXP MCX C series.
Add die temperature measurement configuration.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Bandgap voltage is used for on die temperature measurement. Bandgap
buffer has to be enabled explicitly to get correct tempearature.
Enable the buffer if TEMP_KINETIS is selected.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Commit f987e8c6f0 introduced a regression
where the is_ip check fails if no --id is passed as an argument.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Rework overlays and add sysbuild/vpr_launcher folder to allow standard
test configuration for nrf54h20dk cpuppr.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Rework existing nrf54h20dk overlays to allow adding of
nrf54h20dk//cpuppr target.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In order to allow fiting test in targets with smaller memory make
large buffer configurable through Kconfig.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add support for building NXP WiFi. Since the driver typically requires
binary blobs, enable CONFIG_NXP_WIFI_BUILD_ONLY_MODE for this testcase.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Generated PEM headers need to be created before we build the WiFi shell
when WIFI_NM_WPA_SUPPLICANT_CRYPTO_ENTERPRISE is enabled, so add an
explicit dependency on the app target to be certain these headers are
created
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_MBEDTLS_HAVE_TIME_DATE, which will cause that mbedtls
include Zephyr time.h and leads to 'DIV_ROUND_UP' redefined warning.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Add CONFIG_NXP_WIFI_BUILD_ONLY_MODE, which allows the NXP WiFi driver to
be built without a binary blob. The built application will not be
functional, but this enables continuous integration to run upstream.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
set_btwt API implementation is not complete. Remove the structure
definition and implementation from the NXP WiFi driver to fix a build
error.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Vinayak Kariappa Chettimada