The OpenTitan power manager is responsible for changing the OpenTitan's
operation to and from low power state. This patch adds a simple binding
for the power manager's config registers.
This is part of the OpenTitan watchdog patch series. The power manager
HWIP block needs to be configured to enable the watchdog reset
functionality in the OpenTitan Verilator simulation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Add NPCX Power Switch Logic (PSL) DT node which controls the power rails
of SoC to get better power consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add missing devicetree nodes representing the following peripherals
in nRF SoCs:
- ACL
- BPROT
- CCM
- COMP/LPCOMP
- CTRLAP
- DCNF
- MPU (nRF MPU peripheral in nRF51 Series, not ARM MPU)
- MUTEX
- MWU
- NFCT
- OSCILLATORS
- POWER (in nRF51 and nRF52 Series)
- PPI
- RESET
- SWI
- USBREG
Add also corresponding bindings and validation of base addresses of
these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Exit latency is the maximum time required by a CPU to transition from
a specific idle state to active state. This information is going to be
used to properly configure the wake up event in order to the system be
able to execute the next scheduled task.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
There are platforms that have multiple states that maps to a specific
Zephyr power state. To accommodate this sort of situation this commit
adds an additional property to a power state that can be used by the
platform.
The power state now consists of two properties, a category and a
substate-id. The former property is the current power state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add power state property binding and include this property in cpu.
The pm-state attribute is a enum that matches with enum pm_state right
now the only timing attribute is the minimum residency that is the
minimum time for a power state be worthwhile.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Correct the names of the binding files, so they comply
with binding file naming nomenclature.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Bjarki Arge Andreasen