Adds support for a devicetree property that controls the ClockDiv
value provided to the SDIO during init.
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
STM32L4plus mcu has SDMMC internal DMA which works without any
configuration and it's handled by SDMMC HAL driver. This commit adds
option to enable it and use it.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
This fixes underrun issues when hardware flow control can't be used.
Only tested on STM32F4.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
...
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable pinctrl driver for usdhc. USDHC driver uses custom pinctrl states
for fast, slow, and medium signal frequencies, as well as pin pull for
SD detection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
When 1.8V is disabled, sdhc can only
communicate at low speed. But this can
save the external circuit for switching
between 3.3V and 1.8V, which is very
practical in costdown scenarios.
Signed-off-by: Frank Li <lgl88911@163.com>
The label property does not need to have its type set
explicitly to string, so remove it.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add a disk access driver for the stm32 sdmmc component. The driver is
based around the stm32 cube HAL and uses the blocking API.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Converts the usdhc driver to the new gpio api. Updates the
device tree for the mimxrt1050_evk board to set appropriate active
high/low polarity for the power and card detect pins.
Note that the driver doesn't actually support interrupts yet. It
initializes a gpio callback for the card detect pin, but never actually
enables the gpio interrupt. This incomplete behavior is left as-is,
since the purpose of this patch is only to convert the driver to the new
gpio api, not to add new features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Convert type from compound to phandle-array for various bindings that
have properties like like <FOO>-gpios, pwms, clocks,
interrupt-extended, etc. that are phandle-array's.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Note that these appear as
properties: {erase,write}-block-size: label: ...
rather than as
properties: label: ...
I can't see anything looking at 'label' for individual properties in
bindings, so it's probably dead code. Labels are fetched from the device
tree in extract/flash.py.
Piggyback removal of some 'generation: define's and a redundant pair of
YAML document separators.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
1) dts/bindings/mmc/mmc.yaml: specifies common mmc.
2) dts/bindings/mmc/nxp,imx-usdhc.yaml: specifies
nxp usdhc module which inherits mmc.
3) dts/arm/nxp/nxp_rt.dtsi: usdhc support on RT chip.
4) boards/arm/mimxrt1050_evk/mimxrt1050_evk.dts:
usdhc slot support on mimxrt1050_evk board.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Features:
- Uses the SPI bus to communicate with the card
- Detects and safely rejects SDSC (<= 2 GiB) cards
- Uses the optional CRC support for data integrity
- Retries resumable errors like CRC failure or temporary IO failure
- Works well with ELMFAT
- When used on a device with a FIFO or DMA, achieves >= 310 KiB/s on a
4 MHz bus
Tested on a mix of SanDisk, Samsung, 4V, and ADATA cards from 4 GiB to
32 GiB.
Signed-off-by: Michael Hope <mlhx@google.com>
Maxmillion McLaughlin