The stream flash test has been written with SoC internal
storage in mind and its simplified structure does not take
into account possibility of existence of devices with
different erase characteristics, at run time.
The commit fixes the test failing with Nordic bords that
have CONFIG_SPI_NOR=y set by default, which made test
to behave like device with erase capability has been tested.
The commit sets CONFIG_SPI_NOR=n for nrf54l devices.
Fixes#79181
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add TLS_ECDHE_ECDSA_WITH_AES_128_CCM_8 to the list for use with x509
certificates. The LWM2M v1.1 specification says that a LWM2M client
which used X509 certificates must support this ciphersuite and
additional ciphersuites may be supported.
Signed-off-by: Jeroen Broersen <jbroersen@interact.nl>
Add log statements for each command, event and response
for debugging purposes.
Tests do not send enough of these to clutter the IUT logs
and it is useful for debugging to more easily determine
what command triggered a function call or when the
responses and events are sent to the AutoPTS client.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add a check to ensure that all zephyr_file/zephyr_raw links are pointing
to valid paths in the current zephyr tree.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
In preparation of adding a check for dead references, this commit fixes
currently broken zehpyr_file: links.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
During secure association, if we get any data packets from the
networking stack (as we switch off the dormancy) then they will be
dropped till the 802.1x port is authorized, but with recent changes the
corresponding network buffer isn't freed causing a memory leak.
Handle this case and free the network buffer (Using an OSAL API though
it's Zephyr to avoid duplication and also getting access to "struct
nwb");
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
lots of values from the DT where not set corretly, if
`CONFIG_SPI_NOR_SFDP_RUNTIME` was
enabled. This fixes it.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Without this, check_compliance.py suggests to run clang-format on the
changed code lines.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
This change extends what e1e19732bc
(samples: drivers: crypto: Aligned AES key) has started: For certain
architectures (i.e. Si32), the alignment of the used buffers is
important as the AES HW engine uses DMA and inherits its restrictions.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Commit e1e19732bc (samples: drivers:
crypto: Aligned AES key) introduced the alignment for the key. According
to the commit message, the intention was to align the variable at 32 bit
boundaries. For this reason, passing 32 to __aligned seems like an
error, as its argument is denoted in byte and not bits.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
To accommodate for some slow tests on up2.
For example: tests/arch/x86/info/arch.x86.info.userspace
Execution time of this test is close to 55s and sometimes
above up to the 60s.
Related issue: #80134
Signed-off-by: Artur Wilczak <arturx.wilczak@intel.com>
Fix incorrect header file pre-macro names in
'include/zephyr/app_memory', 'include/zephyr/display'
and 'include/zephyr/mgmt'.
Signed-off-by: James Roy <rruuaanng@outlook.com>
The MCUmgr statistics only work correctly when selecting
MCUMGR_SMP_LEGACY_RC_BEHAVIOUR option. Checks the option
flag on the stat_mgmt_list and fix the behavior.
Fixes: 80476
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
LTO support was added with Zephyr 3.6.0, and it has been used in
production with Nordic devices for a long time. Remove the experimental
label to mark it ready for production.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Set soc_root using Path to avoid wrong generated path in the list of
soc_roots and other roots read from module.yml file
Fixes#80531
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds a missing 'default y' for the Kconfig option indicating that
encryption is supported with the current configuration
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
`+C*REG:` may be received as AT read command answer
or unsolicited notification.
Their syntax differs, and even the overall parameter count varies
depending on what `<n>` is used in the `AT+CEREG=` write command.
To handle all cases properly, check the parameter count and
the presence of the `<tac>` parameter (which is a string and
thus begins with `"`) to figure out what is the position of `<stat>`.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Main changes since v2.3:
* Support for immediate RSSI measurements during abort reevaluations
* Several minor improvements in the base components, including
tolerating better under-setup docker images, improved C++
compatibility, a new sanity check for problematic user provided
sim_ids, and other minor improvements.
Note: Like before, bsim remains fully backwards compatible
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commits defines the `#power-domain-cells` properties for fakedomain
nodes in the HiFive Unmatched devicetree overlay file.
Without this change, this tests fails to build for the `hifive_unmatched`
Zephyr target.
Fixes#80503.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Do not select HAS_SEGGER_RTT unless the segger module is present. This
avoids a Kconfig error when SEGGER's debug module is not present in the
west manifest
Fixes#80529
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The coprocessor number in ARM `mrc` and `mcr` instructions must be prefixed
with `p`.
GNU assembler allows specifying coprocessor number without the `p` prefix;
but, LLVM assembler is more picky about this and prints out "invalid
instruction" error otherwise.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Fixed typo in Renesas RA SCI UART configuration that was preventing
hardware flow control from being enabled.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Remove wifi sample config files for esp32c2/esp8684, as device
isn't able to run it after memory layout update.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
this flushes the rx buffer before the
start of a new transaction. It is needed
because the litex bios is not always
reading the rx buffer.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
This reverts commit 6d4031f96c.
Those makes majority of builds og platforms with blobs tainted although
the blob were not used or compiled in. So it is very misleading.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
when no rx data need to be read set the rxignore bits.
with this change the dma setup is faster and no unnecessary
dummy writes are done to memory.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
when sending multiple bytes only the DMA_STATUS_COMPLETE
status is interesting. otherwise the semaphore will be signaled twice.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
There is a typo in the part number list for LPC55S69. The
LPC55S69JET98 should be LPC55S69JEV98.
Fixes#80541
Signed-off-by: David Leach <david.leach@nxp.com>
It's not possible to get pinconfig of specific pin
in ambiq_gpio_port_get_raw function, change to use
OR value of RD and WT registers for one group of gpio.
Signed-off-by: Hao Luo <hluo@ambiq.com>
Instead of forcing a definition in Devicetree. Right now, SoC DT files
contain this default, but it should not be part of SoC DT files.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add variant for the coex interface and move the coex interface out
if the wifi/control interface variants.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Exclude the coex interface if the coex variant of the nrf7002eb
is selected instead of adding the interface alongside the
wifi/control interface.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The nrf7000, nrf7001 and nrf7002 expose a coex hardware interface
which is independent from the wifi/control interface (spi and
control pins)
These interfaces where previously combined into a single model. This
is incompatible with the actual usage of the interfaces where one
core may interact only with the coex interface, and another with the
wifi/control interface.
This commit moves the coex interface, commonly described in
"nordic,nrf70-coex.yaml", out of the wifi/control models
"nrf700<variant>-<bus>.yaml" to its own models
"nrf700<variant>-coex.yaml"
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Larger image partitions require more space in DRAM due to
the increase in .bss.sector_buffers.
Each sector in .bss.sector_buffers consumes 16 bytes.
In the worst case scenario, such as with the ESP32S3 N32R8V,
which has 32 MB of flash and most likely 12 MB image partition,
an addition of 0xc000 should be sufficient to accommodate this.
Signed-off-by: Nik Schewtschuk <nikita.schewtschuk@smartmechatronics.de>
This header requires bluetooth.h but was not including it itself.
Due to this we had 2 tests failing to build.
Let's just include the dependencies to this header instead of
relaying on users including the dependencies dependencies in
the right order.
Also, let's add an include guard as in a test this header was
included twice leading to weird build errors.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
In 82d8f09de1
the bt_conn_foreach prototype was changed, but these unit tests
kept using the old prototype which leads to a build warning.
Let's fix the prototype in the tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
- Modify the macro in source code AGT to get the right data from
device tree
- Modify name of agt node
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
uart_irq_tx_complete is implemented by z_uart_async_to_irq_irq_tx_ready
which changed recently (5bd53b6e2) to return positive value that may be
bigger than 1. uart_irq_tx_complete shall not return value bigger
than 1.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Added casts to uint32_t in arch_timing_cycles_get() to handle the
wrap-around of the 32-bit cycle counter correctly.
Signed-off-by: Simon Tomschik <simon.tomschik@askgroup.global>
This is a bug fix for adxl345_accel_convert_q31 functions.
Functions are used to convert samples received from
sensor to q31_t format when RTIO stream is used.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Dominik Ermel