The network tests were expecting that network interfaces
are in certain order. As we cannot guarantee that, refactor
the tests like this:
* if test is using DUMMY L2 driver, then disable Ethernet L2
and fetch only DUMMY L2 instead of default interface
* if test is using Ethernet L2 driver, then make sure that the
test is using the Ethernet interface specified in the test
instead of the one provided by the DUT
Fixes#34505
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to increase the stack sizes if user enables CONFIG_COVERAGE
option. You can test this by this command
sanitycheck --coverage -p qemu_x86 -T tests/net/udp \
-T tests/net/mgmt -T tests/net/mld
This is partial fix for issues described in #17323
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There were various flaws in it that motivated its removal:
- No hash collision handling mechanism. In case that would happen, the
behavior of the network connection would be unknown. This is the main
drawback
- The lookup is not that much more efficient than the default one. The
only difference of gain is in connection comparison (a u32t comparison
vs a full connection compare). But the list handling is the same. It's
made worse by the presence of a negatives match array which can be
easily filled in and becomes then fully usless, appart from consuming
CPU. As well as adding a new connection: it requires the whole cache
to be cleared which is unefficient.
- Not memory efficient, even compared to a proper hash table.
Two arrays instead of one etc...
All of this could be fixed by using a proper hash table, though it
remains to be seen if such object could fit in Zephyr core.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In some hw like Atmel SAM-E70, the original amount of network
buffers is too small so increasing it slightly.
Also generate proper error if this happens in the test so it
is easier to figure out.
Fixes#8865
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
- replaced test points with ztest APIs wherever possible
- replaced CONFIG_MAIN_STACK_SIZE with CONFIG_ZTEST_STACKSIZE
in config file
JIRA: ZEP-2249
Signed-off-by: Niranjhana N <niranjhana.n@intel.com>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_NET_IF_UNICAST_IPV6_ADDR_COUNT should be used instead of
CONFIG_NET_IFACE_UNICAST_IPV6_ADDR_COUNT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We did not check UDP or TCP checksum to be valid after receiving
the packet. Fix this so that the checksum is validated when
packet is received in connection handler. As the checksum validation
can be resource intensive, do it after we have verified that
there is a connection handler for this connection.
The checksum calculation can be turned OFF if needed, but it is
ON by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The option is no longer used so it can be removed.
Use CONFIG_NET_IPV6_ND option instead.
Change-Id: Ibaa3d3deb52b8b176e85f8b9e1d8c80c1026aea1
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Rename project configuration to be architecture independent and do not use ARCH
in Makefile.
Change-Id: Ic793751e3187bc74fd14cec929754d691b01a799
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Xiao Song