GDB server needs ownership of some exceptions to display information when
taking a fatal exception (DIVIDE_ERROR, PAGE_FAULT).
Introduce a Kconfig option that can work for any debugger.
Change-Id: I39aef22a820543a7fe9ac333b487592946abc0f3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The GDB server implements a set of GDB commands, such as read/write
memory, read/write registers, connect/detach, breakpoints, single-step,
continue. It is not OS-aware, and thus provides a 'system-level'
debugging environment, where the system stops when debugging (such as
handling a breakpoint or single-stepping).
It currently only works over a serial line, taking over the
uart_console. If target code prints over the console, the GDB server
intecepts them and does not send the characters directly over the serial
line, but rather wraps them in a packet handled by the GDB client.
Change-Id: Ic4b82e81b5a575831c01af7b476767234fbf74f7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Introduce an x86 interrupt stack frame that contains more information
than the non-debug one, namely the caller-saved GPRs, as well as an API
to retrieve it. Able to handle nested interrupts stack frames.
Change-Id: If182aaa2f34e4714b16ca65ff79da63b72d962f7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Allow a debug server such a GDB to take control when a fatal error
occurs. The debug server simply has to define a _debug_fatal_hook()
function that will override the weak function installed by default.
Change-Id: Ib9dca5755868f747b697fa3178e09109f1eedb07
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Quark flash sub-driver. It is based on the QMSI driver.
In order to enable this driver, the following options
must be set.
CONFIG_QMSI_DRIVERS
CONFIG_QMSI_INSTALL_PATH
CONFIG_FLASH
CONFIG_SOC_FLASH_QMSI
Origin: Original
Change-Id: Iffbea3b17624c755e367677b76d7216c2fba2ca1
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The D2000 CRB is similar to the Arduino 101 (at least as GPIO is
concerned). Add support for using the GPIO controller without QMSI
libraries.
Change-Id: I001da05c9a9d5771b2ec678a9d4a91c44db05289
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib483419be5199b52cf281b4b106cd8a3be95b7be
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove UART default configuration to make it default UART_0. This
makes default working fine with Nordic BLE chip using H:4 driver.
Change-Id: Icb6d9f068b586bbf04694bc77ed968211de94c8a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Allow to connect Nordic Devkit or dongle to qemu. Simple
configuration for the current NBLE firmware is following:
Connect Nordic board to PC, ttyACMX gets created.
$ socat -x /dev/ttyACMX,raw,b1000000 unix-listen:/tmp/bt-server-bredr
Build app with prj_nble.conf and run with make qemu
Change-Id: I354644b465ad09ab0ca62fbd97f15d9bb3c87d6a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib7e0b81b2df1a0225fc244fea3035416d0a4f282
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
This also separates IRQ_PRI into one for DW and one
for QMSI, to follow the convention of every other
drivers.
Change-Id: I338f819f71c18fa9e17015e8a588a3d0207350c6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ic73783189db57059d2b7f3727e4802e1b2e27931
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifdbb5e3a997795ef577350d88f8cb06877eb6463
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib8158f00a6c6616360ddbcf63981f1a85911c1b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch extends the i2c shim driver so it supports the 'default
configuration' infrastructure which enables the user to specify a
default configuration for the I2C device. The default configuration
is set during driver initialization.
This patch also changes Quark SE and D2000 Kconfig.defconfig files so
the i2c default configuration is set to '0x12' which means standard
bus speed, 7-bit addressing and master mode. This is the same value
used when DW driver is selected, by the way.
Change-Id: I06e0dc3c29e8da2f3317db5bef285177f2e92c9a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Remove those kconfig options that are SoC specific, and should not be
configurable via kconfig.
Change-Id: Ia62888838877da4627419bd36c261d5254761acd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It wasn't correct to add the size of the long jump instruction
as it *replaces* a short jump instead of just being after it.
So redefine this to be the difference in size between these
two instructions.
Change-Id: I65be2afab19d9cd8b096551acde0156f0503df87
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These interrupt settings are SOC specific. So, move them to the
SOC level of Kconfig.
As IRQ priority is fixed in D2000, changed the value to 0 to
make it consistent with what other shim drivers are using.
Change-Id: Id20bed46c478a7555ae976e3a3063ba2cb099788
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This is hardware design so there is no need for it to be
configurable in kconfig.
Change-Id: Iff162f330aae8ef9a7139b6e7ed9bfa87f26189a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IRQ triggering condition should be specified by SoC as it is
a decision for hardware design. This should not be configurable
in kconfig.
The default is to be triggered on rising edge, just as the same
old kconfig did.
Change-Id: If59d88a30711eb8e03d9cc4f409055cefe1995c5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves those kconfig options which should be declared in
SoC or board header files instead. These are the one
that are tied to SoC or board and there is no need
for them to be configurable in kconfig.
Change-Id: I243d634f1a4a11dc8dc3530d95f93371015492b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: Iab10655c6fc6f17c0c6dd49cb7a4e74fabcf852c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: I3a51b35e633dc7b1b841e9fa504bf0cfc0d4d575
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Changed names of Kconfig flags, variables, functions, files and
return codes consistent with names used in the RFC. Updated
relevant comments to match the changes.
Origin: Original
Change-Id: Ie7941032d7ad7af61fc02928f74538745e7966e8
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch replaces all occurrences of DEV_* codes by errno.h codes at
the arch layer.
Change-Id: I1a1ab6d0481f3660ad032e2690d2577245fe1f34
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch fixes the QMSI UART shim driver so we are able to use it in
Quark D2000 based platforms. Differently from Quark SE, the peripheral
clock gate bit (CLK_PERIPH_CLK) is not enabled by default in Quark
D2000. We have to explicitly set this bit in order to properly initialize
the device.
Since this drivers is now properly working on Quark D2000, this patch
also sets the QMSI driver default options in arch/x86/soc/quark_d2000/
Kconfig.
Change-Id: I817b7703554be162ac628dcd8d3d07512b9eb3f5
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
() Moves the Quark SE clock control into its submenu.
() Fixes the dependencies in the SoC default Kconfig
so the options are not displayed out of place in
menuconfig.
Change-Id: Ifdf06242be8ceed03c2c657c942875a5a7f2750e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC selections for each architecture are moved to the top level
in menuconfig and xconfig. This makes it more intuitive to select
architecture -> SoC -> then board, avoiding an additional trip to
go into the architecture menu to select SoC.
Change-Id: I57a78a09adfc4bb12423915b6ad14ceb74381a2b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It makes no sense to allow enabling support for floating point
registers when the CPU has no FPU.
Change-Id: If51187033fc84957721d87fa6e79ef31124f4b14
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
These options should be selected by individual SoC automatically,
and should not be visible options. Or else it would be possible to
select Quark SoCs and telling Kconfig it is from Atom family (which
is incorrect).
Change-Id: I17a6cf713378333e0e7942aa49b381b5eb9526b5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When building with IAMCU, make sure we set the soft-float, otherwise
build would fail with unsupported instruction errors.
JIRA: ZEP-103
Change-Id: I7a5f107a2df50799a7f6dd4aba36c1a977c1461d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This creates the QMSI comparator driver which is simply a shim driver
based on the comparator driver provided by QMSI BSP.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_AIO_COMPARATOR=y
CONFIG_AIO_QMSI_COMPARATOR=y
Origin of the file: Original
Change-Id: Iad01cb80f7bb1eff1710cd76cd0afeb70c311e04
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This patch extends the UART QMSI driver so it supports the IRQ APIs from
include/uart.h. The IRQ APIs are enabled by the 'CONFIG_UART_INTERRUPT_
DRIVEN' option.
Differently from others APIs such as I2C and SPI, the UART API is very
low level. For that reason, the IRQ facilities (e.g. irq based transfers)
from the QMSI driver are not useful to the shim driver at the moment. In
order to implement the IRQ APIs we rely on UART registers defined by QMSI.
QMSI UART header is missing some macro definitions from IRR register so
we define them in the shim driver.
Since the IRQ trigger condition is not configurable in the QMSI shim
driver, this patch also changes drivers/serial/Kconfig so the "UART
IRQ Trigger Condition" choice doesn't appear on the menu if the QMSI
driver is selected.
Change-Id: Idf9a0f6a47af2a550a31f474d721068dca989713
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the QMSI UART driver which is simply a shim driver
based on UART driver provided by QMSI BSP.
This initial version implements only the mandatory APIs 'poll_in',
'poll_out' and 'err_check' which are required by trivial sample apps and
by output functionality from the console driver. The remaining APIs will
be implemented by up coming patches. The driver supports only 115200 baud
rate at the moment.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_SERIAL=y
CONFIG_UART_QMSI=y
This driver has been tested with Quark SE Devboard so this patch also
adds its platform-specific default configuration options to 'arch/x86/
soc/quark_se/Kconfig'.
Change-Id: Ibde1825d4b0349a376a8e7d91cc9de306946b62f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The thread monitor allows to iterate over the thread context
structures for each existing thread (fiber/task) in the system.
Thread context structures do not expose thread entry information
directly. Although all the information can be scavenged from memory
stacks. Besides, accessing the information depends on the stack
implementation for each architecture.
By extending the tcs we allow a direct access to the thread
entry point and its parameters, only when thread monitor is
enabled.
It also allows a task to access its kernel task structure
through the first parameter of the thread.
This allows a debugger application to access the information directly
from the thread context structures list.
Change-Id: I0a435942b80eddffdf405016ac4056eb7aa1239c
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
This patch removes the macro UART_IOAPIC_FLAGS from Quark SE and D2000
soc.h since it is not used anywhere in the code.
Change-Id: I0fd42fac2f02e8617bd92c73c1a0354ef2d7a71a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
One of the tricks that GCC's stack protector does is to stick a
sentinel value on the stack at the beginning of the function, and
check if it is still there when the function is about to return.
However, since this function switches stacks that fails and we get
a stack protector exception before main() even starts.
Change-Id: I2acba8b8c822d7447d8e371bb72603f36e87f54b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Remove CPU_MIGHT_SUPPORT_CLFLUSH as excessive.
Removal the flag requires adding per-SoC cnfiguration,
as some Quark models support clflush instruction, but
some do not, even on compiler level.
Change-Id: I655cba00c629db55d1813c199a2fe08b2d60ef4f
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Rearrange the source code in order to place functions
depending on clflush support detection into the proper
section.
Removed dependency between CACHE_LINE_SIZE_DETECT and
CLFLUSH_INSTRUCTION_SUPPORTED or CONFIG_CLFLUSH_DETECT.
Change-Id: I62ba5199763ed16c71f1d2fa372f6cc99b303e6a
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clockgating was disabled for RTC and disabling RTC had no
effect on Quark SE boards.
Change-Id: I67448d5582a206fc7a68d763d504e9f743043b53
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Benjamin Walsh