vl53l0x driver is using an external library to build, located under:
ext/hal/st/lib/sensor/vl53l0x.
This library is expecting stdint.h lib to be available and to
secure this for driver library inclusion work, a stdint.h file
header check was done. This check was based on assumptions on possible
header names for stdint.h.
Due to recent renaming of the zephyr header files, this check was
returning a false positive, generating warning at compilation.
Rather than updated with new header names, remove this check, since
driver porting is completed and stdint.h inclusion is actually
done.
Fixes#10134
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Generate interrupt on every ALS cycle in non-trigger mode
and enable ALS saturation interrupt.
resolves: #11989
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add support to STM LIS2DW12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Co-authored-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new i2c_write_read() wrapper to simplify the code.
Also add several overlays used to test the sensor on a variety of
boards, and conf file support for trigger testing.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We use DT to get the I2C address, so the define that got it from a
Kconfig sybmol isn't used and the Kconfig symbol isnt defined. Remove
this dead code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning with sdk-ng:
drivers/sensor/lis2dh/lis2dh.c:210:38: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((value & LIS2DH_LP_EN_BIT_MASK) == 1 && ...
^~
The test needs to be:
(value & LIS2DH_LP_EN_BIT_MASK) == LIS2DH_LP_EN_BIT_MASK
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This belongs in the implementation file that references the array, since
the header is included in multiple files.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Setting bit 3 instead of bit 2 modifies a reserved section of the
register, with the impact that the ODR is not as configured.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use Kconfig named choice for TRIGGER_MODE in order to easy
up the trigger mode selection in default configurations
for boards using this sensor driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2DH driver to avoid
usage of dts.fixup files. The triggered interrupt part has been
slightly hacked to automatically understand whether only int1 is
configured or both int1 and int2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LIS2DS12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Currently it uses high resolution only as power mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a configuration structure to sht3xd that holds instance-specific
parameters, implemented in a immutable statically allocated object
initialized with material from device tree binding aliases.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Change driver to get I2C address of sensor from the device tree like
most other sensor drivers that utilize device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the value for Low Power Enable (LP_EN) bit mask.
(Issue described by Coverity CID #188734)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm9ds0_gyro driver to get the device name as well as
i2c slave information and gpio info for triggers from device tree.
Updates the build_all test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Piotr Zięcik