In update the Kconfig to depend on devicetree, the SAM4L
driver was missing a 'default y'.
Also remove unnecessary 'depends on GPIO'.
Signed-off-by: Kumar Gala <galak@kernel.org>
Update gpio drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
The SAM spi driver depends on GPIO driver to work. It seems that this
dependency chain it is not handled. This select GPIO driver when SPI
driver is enabled. It rework GPIO and SPI Kconfig to select driver by
devicetree and drop entries at Kconfig.defconfig.series file.
Fixes#41525
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
All GPIO controller drivers support DTS so we can select HAS_DTS_GPIO
at the GPIO driver subsystem level rather than for each specific driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Most of these are from source'ing a file within an 'if GPIO', and then
adding another 'depends on GPIO' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Selects HAS_DTS_GPIO in various gpio drivers that already support dts,
similar to how we select HAS_DTS_SPI in spi drivers and HAS_DTS_I2C in
i2c drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Piggyback a missing 'source "drivers/gpio/Kconfig.imx"'. This file
wasn't included anywhere previously.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Kumar Gala