No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support to STM IIS3DHHC the ultra-low noise, high-stability
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LIS2MDL is not a combo device, but pure magnotemeter.
Hence, '-magn' extension is not adding information and can
be removed from dts compatible name as well as binding filename.
Instead specify '-i2c' or '-spi' to distinguish between the names.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
After the window watchdog introduction, the boards that support it over
independent watchdog fail to pass this test. This patch adds specific
tests for the nucleo_{f401re, l496zg} boards supporting WWDG.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
This has been subsumed by the new implementation in drivers/pcie.
We remove the legacy subsystem, related tests, shell module, and
outdated documentation/config references.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
this case isn't designed for SMP, setting CONFIG_MP_NUM_CPUS=1 to
run the full SMP kernel config, but with only one CPU available.
Fixes: #12478.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
No test verifies a TX callback for successful transfers.
This commit adds a test for those callbacks.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The mcux pwm drivers use period cycles as a divisor to calculate the pwm
frequency in hertz. This operation can underflow easily with large
values of period cycles relative to the pwm clock source, causing the
driver to return an error code and the pwm_api test to fail.
Updates the test to use the smaller set of period and pulse cycles on
k64-based boards, fixing the test for frdm_k64f and hexiwear_k64 boards.
The test is not changed for i.mx rt boards because the pwm clock source
on these boards is much faster than on k64 boards, and thus the same pwm
frequency operation does not underflow.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add SPI support for stm32mp157c_dk2 board. If SPI is selected, SPI4
(Arduino connector compatible SPI) and SPI5 (on front 2x20 GPIO
expander) will be enable by default on stm32mp157c_dk2 board.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
We generated a define for each instance to convey its existance of the
form:
#define DT_<COMPAT>_<INSTANCE> 1
However we renamed all other instance defines to be of the form
DT_INST_<INSTANCE>_<FOO>. To make things consistent we now generate a
define of the form:
#define DT_INST_<INSTANCE>_<COMPAT> 1
We also now deprecate the DT_<COMPAT>_<INSTANCE> form and fixup all uses
to use the new form.
Fixes: #17650
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These additional configs should have been put in prj.conf
and not here. Makes the tests simpler to build correctly
outside of sanitycheck.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Flash size calculation was don with assumption that flash page size
is always 1 KB and flash size was parameterized with such granularity.
This patch correct this bug.
Flash pages number under statistic can't be calculated via preprocessor
anymore - thus are parameterized via Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It Need to start using DT_FLASH_SIM_xxx labels after sim_flash was
un-chosen as zephyr,flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove whitelisting and make the test more generic. This test was only
building on 1 board basically, now with the new filters it builds on 24.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove whitelisting and enable broader testing on all boards with needed
features.
Add pwm to board yaml where it applies.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
uint8_array values are now generated as structure initializers. Update
the code accordingly. The implementation assumes that existing
devicetree source does not provide the correct OUI so preserves the
in-driver override of the value provided by devicetree.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Flags in alarm configuration structure will allow further extention
without breaking API. Initially, existing absolute flag was added
as the only flag.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add support to STM LSM6DSO 6-axis IMU sensor driver.
This driver supports communication with device though both
I2C and SPI bus and both polling and drdy trigger mode.
This driver supports also the sensorhub mode with the possibility
to connect a maximum of two external devices, typically a
magnetometer and an environmental sensor, currently selected among
following devices: lis2mdl magnetometer, lps22hh or lps22hb
pressure and temperature sensors, HTS221 humidity sensor.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LPS22HH pressure and temperature sensor.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move rtc.h to drivers/rtc.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pwm.h to drivers/pwm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ipm.h to drivers/ipm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2s.h to drivers/i2s.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move hwinfo.h to drivers/hwinfo.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move entropy.h to drivers/entropy.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Takumi Ando