Moves all Renesas sensor drivers into a vendor specific subdirectory
matching the organization used for other drivers.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Refactors the cmake and kconfig bits of the tdk sensor drivers into the
vendor subdirectory to make them consistent with other vendor-sorted
sensor drivers. The tdk driver implementations were previously moved
into the vendor subdirectory in commit
41f1c3a2b7.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
This transforms the existing driver for the Microchip MCP9808
to be used as a generic driver to be used with all
JEDEC JC 42.4 compliant temperature sensor chips.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Add driver for Festo VEAA-X-3 series proportional pressure regulator.
The driver assumes that the maximum ADC value matches the maximum
output from the device, and that the maximum DAC value matches the
maximum input value for the device. External hardware is probably
required between the ADC/DAC and the device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add driver for TSic 206/306/316/506F/516/716 temperature sensor.
The driver uses PWM capture driver to read a single wire with
Manchester-like encoding.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The DHT20 sensor is a temperature and humidity sensor that uses I2C to
communicate with a microcontroller. The DHT20 sensor is Aosong.
use standard crc
update description to add reference to AHT20 and AM2301B
clean code, use defines and bit manipulation
add dht20 to i2c test suite for build tests
update bit manipulation
use more defines instead of raw numbers
add bindings to allow aht20 or am2301b to be used in devicetree
in all 3 cases, the same dht20.c driver is compiled
Signed-off-by: Nathan Olff <nathan@kickmaker.net>
Add driver for Angst+Pfister O2 sensors FCX-MLD25 & FCX-MLD95 and maybe
more. Tested with FCX-MLD25.
Supports get O2 value, get status, and power management.
Note that in suspended power mode heating output is at 20 %, thus
probably not suited for a battery powered device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The STTS22H is an ultralow-power, high-accuracy, digital temperature
sensor offering high performance over the entire operating temperature
range. This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/resource/en/datasheet/stts22h.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Implement a sensor for the output diagnostics of the low side
switch BD8LB600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add driver for ScioSense ENS160 multi-gas sensor. The driver includes
support for I2C and SPI, attributes for setting temperature and
humidity compensation and data ready trigger.
Also add ScioSense to the list of vendor prefixes.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
The LIS2DE12 is an ultra-low-power high- performance three-axis
linear accelerometer belonging to the “femto” family with digital
I2C/SPI serial interface standard output.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lis2de12.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds source and header files required for bmp581 I2C driver.
I have used bmp581_user.h to add more usage related definitions
but bmp581.h to add hardware related definitions.
Signed-off-by: Talha Can Havadar <havadartalha@gmail.com>
Signed-off-by: Gerhard Jörges <joerges@metratec.com>
This is a driver targetting the Bosch BMA 4-series accelerometers. It
has been specifically developed for the BMA422 but should be compatible
with others in that line, excepting the BMA400. Supports key attributes
and async RTIO one-shot operation. I2C operation is supported, with
stubs for a SPI implementation provided for future improvement.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
Daniel Kampert