This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: Idaaa0d705a31bc69cdf7e576e303f581d3d0bd5f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In ST CMSIS files, FLASH_BASE does not mean base address of FLASH register
Instead FLASH_R_BASE is used.
stm32f1 clock control driver is updated to be compatible with this naming.
Change-Id: Ic4fb49c60c392e15fd12c69266baf4c686bd343b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support for use of HSE (incorrectly named PREDIV1)as input of PLL,
along with HSE bypass for stabilized external clock, and XTPRE
prescaler. Update PLL handling so that we do not unnecessarily enable
PLL clocks, instead enabling only the clocks sources that are required
as per user's configuration.
This change allows higher SYSCLK clock values, up to 72MHz.
Change-Id: Ia7c2be3ce11ac0de2efa664b20e7ab5fddd57a51
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The patch adds a driver for STM32F10x series RCC (Reset and Clock
Control) subsystem.
The module is primarily responsible for setting up of MCU's clock
tree. In particular the driver sets up SYSCLK, PLL (with source
configuration), AHB prescaler, and APB1/APB2 prescalers. As part of this
functionality, the subsystem can enable/disable clock signal for
particular peripherals, thus reducing the power consumption of the MCU.
The driver implements clock control driver API. However, subsystem IDs
being HW specific are exposed in driver public header that must be
included by callers. The driver registers a single device using a common
name STM32_CLOCK_CONTROL_NAME. The device is initialized at
the PRIMARY level with priority 1. This allows the initialization to
take place right after SoC initialization routine.
The driver depends on selection of SOC_STM32F1X config option and is MCU
specific.
Change-Id: I8bea5db20726a24bce7b7ffe0b95de543240429a
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Vincenzo Frascino