The exticrX registers were shifted by a word, so configuring
an EXTI line on a port different of PA misconfigured the EXTI line
source and could flood with unwanted events.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
stm32f417xe and stm32f417xg have been introduced with 2
different defconfig files. Since same code is declared
in both files, mutualize declarations in a single file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The enumerations stm32{f3,f4}x_pin_config_mode aren't used any
more. This patch removes them.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
When we mask out the GPIO High impedance/Pull-up/Pull-down field we
should be shifting the mask file, not shifting the field. This is
because all the other defines already assume the shift.
Coverity-CID: 173640
Jira: ZEP-2538
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In the stm32_gpio_flags_to_conf function the configuration
values of the GPIO pin are shifted two times. One in the
stm32-pinctrlf1 header and one in the function. This patch
removes one of those shifts.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Since not all socs from f3 series (i.e stm32f334x8 no MPU) have MPU
capability, add capability only for MPU capable socs in Kconfig.soc
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
As other stm32 series support MPU, move common file in a file tree
useable by socs from other series
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
Neil Armstrong