This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
It is envisaged that this will be used by SoC or board code to make
available fixed purpose memory-mapped i/o registers to the rest of the
system which normally expects to use GPIO devices, e.g. for driving chip
select lines, LEDs or reading button states.
As such, the driver code doesn't provide a kconfig based configuration
mechanism, instead SoC/board code can hard-wire the devices it wants
with something simple like:
GPIO_MMIO32_INIT(misc_reg1, "MISC1", 0x12345678, 0xffffffffu)
Then, for example, if bit N of the register at 0x12345678 is wired up as
an SPI device chip select line, the SPI driver could be configured to
use pin N of the "MISC1" GPIO driver and not need any other board
specific code.
Change-Id: Ib02fcbab73fcf9637e25834db060fb3108626f47
Signed-off-by: Jon Medhurst <tixy@linaro.org>
tested with blinky, button and disco apps
Change-Id: I4b520d4f3e42c97e4a723747ce4a6c67ca9f1d18
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new mcux gpio driver that can be used for k64 and other Kinetis
SoCs. This driver uses mcux CMSIS register accesses to the GPIO and PORT
modules. Some of the logic from the k64 gpio driver was reused and
refactored (mainly flag parsing and callback handling).
Jira: ZEP-1394
Change-Id: If5e9390861c181ec555dce6569b14debb729526a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The driver is currently used only by the ARM Beetle platform.
Jira: ZEP-1245
Change-Id: I6611edd7486a3c6d82d66a9a96c5d4860dad1539
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It's unused anywhere and unlikely to be in the future.
Change-Id: I57926e91da7d31ef6ddda4f86e6dac103dbfa176
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In 1.0 you could set only one callback on the whole gpio controller. It
was impossible for another sub-system to add another callback, without
overwritting an existing one.
Such API has been obsolete for a long time and no one is using it
anymore. Thus removing it entirely.
Change-Id: I6a17fd99373dc6cef1fa2ebb421e992412d5015e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add QMSI 1.1 based GPIO sub-driver for sensor system.
Origin: Original
Change-Id: Ida5565a5911eb55651a11a4ac0b240c624f8e1ca
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Many sub-systems might require to set a callback on different pins.
Thus enabling it via changing the API.
It is also possible to retrieve private-data in the callback handler
using CONTAINER_OF() macro (include/misc/util.h).
Former API is still available, and is emulated through the new one.
Using both should not be a problem as it's using new API calls.
However, it's now better to start using the new API.
Change-Id: Id16594202905976cc524775d1cd3592b54a84514
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The driver implements a GPIO device interface for STM32 MCUs. Each SoC
must provide implementation of the follwoing calls:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(),
stm32_gpio_set(). Consult gpio_stm32.h header for details on semantics
of these calls.
The driver registers 5 devices, each corresponding to a single GPIO
port. The users can then access individual pins by using values
0-15.
Change-Id: Id236b5b75c9dd091018a50a7be3501c8591cd551
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Basic driver support for the Freescale K64 GPIO module.
Note that only pin direction, read and write are supported.
Change-Id: I6587bb260197a00497be9ac991002e3dde54718d
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
The PIO controllers on Atmel SAM3 family processors can be
used for GPIOs, so this is the driver.
Change-Id: I3d5712f3a0a71025b820ca1c08dd767ee1e136d8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Introduce the GPIO QMSI-based implementation. This is basically a
shim layer that implement's Zephyr's GPIO APIs on top of QMSI drivers.
This is an alternative driver that conflicts with the previous
GPIO_DW implementation. In order to enable it you must set:
- CONFIG_GPIO=n
- CONFIG_GPIO_QMSI=y
- CONFIG_GPIO_0=y
- CONFIG_QMSI_DRIVERS=y
- CONFIG_QMSI_INTALL_PATH="PATH_TO_QMSI"
Note that this driver currently only supports one controller instance,
GPIO_0. It is implemented this way due to a limitation from the current
version of QMSI. QMSI versions later than 1.0 doesn't have this
limitation.
Missing:
- support multiple controller instances (gpio_0, gpio_1, etc);
- enable level triggered interrupts in sync with system clock,
through setting INT_CLOCK_SYNC properly.
Change-Id: Ib61b153dae9741806a9a31d7dc1f82b96d000fbe
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Such controller is found in legacy bridge on Intel's platforms. Such as
Poulsbo or Quark x1000.
Change-Id: I30f205f1e73aaa680092e92717fdacbb74046fa3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The naming convention used in the source is for there to be an
_ and not a - in the file. Fixing GPIO to be consistent with
the os naming conventions.
Change-Id: Ifc4356c14b52e2cc2411a7445b44c7cb57d2765c
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
This adds a simple driver for MMIO-based GPIO ports.
It does not trigger any interrupts due to pin level at this moment.
Change-Id: I0c439f221988817e4be72653c68257ef6ace5bde
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the driver for I2C-based PCAL9535A GPIO chip.
This currently only enables minimal set of features of the chip for
very simple input/output operations, and does not support interrupt
yet.
Change-Id: I32ea07a71a38866280a96e68cff49cb0df12b85d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
[DL: captilize commit message title; fixed some whitespaces;
changed the __initconfig_gpio_* from level 0 to level 1,
which is the level of pure_init; and added include path
to board.h; ]
Change-Id: I7eea6a6ca9e4b7cf8d1ccabb57f07f786da93ef0
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Christian Taedcke