With most boards there's no simple way to get access to the HCI
traffic. Simultaneously these boards only have one external UART for
the console. This patch introduces a protocol which combines both
normal logs and HCI logs over a single binary protocol sent over the
console UART.
The protocol is modeled based on the btsnoop/monitor protocols used by
BlueZ, and the first tool that's able to decode this is btmon from
BlueZ ("btmon --tty <tty>").
For platforms with two or more external UARTs it is still possible to
use CONFIG_UART_CONSOLE as long as the UART devices used are
different, however on platforms with a single external UART
UART_CONSOLE should be disabled if BLUETOOTH_DEBUG_MONITOR is enabled
(in this case printk/printf get encoded to the monitor protocol).
Origin: Original
Change-Id: I9d3997c7a06fe48e7decb212b2ac9bd8b8f9b74c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Quark flash sub-driver. It is based on the QMSI driver.
In order to enable this driver, the following options
must be set.
CONFIG_QMSI_DRIVERS
CONFIG_QMSI_INSTALL_PATH
CONFIG_FLASH
CONFIG_SOC_FLASH_QMSI
Origin: Original
Change-Id: Iffbea3b17624c755e367677b76d7216c2fba2ca1
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The D2000 CRB is similar to the Arduino 101 (at least as GPIO is
concerned). Add support for using the GPIO controller without QMSI
libraries.
Change-Id: I001da05c9a9d5771b2ec678a9d4a91c44db05289
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib483419be5199b52cf281b4b106cd8a3be95b7be
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove UART default configuration to make it default UART_0. This
makes default working fine with Nordic BLE chip using H:4 driver.
Change-Id: Icb6d9f068b586bbf04694bc77ed968211de94c8a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Allow to connect Nordic Devkit or dongle to qemu. Simple
configuration for the current NBLE firmware is following:
Connect Nordic board to PC, ttyACMX gets created.
$ socat -x /dev/ttyACMX,raw,b1000000 unix-listen:/tmp/bt-server-bredr
Build app with prj_nble.conf and run with make qemu
Change-Id: I354644b465ad09ab0ca62fbd97f15d9bb3c87d6a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib7e0b81b2df1a0225fc244fea3035416d0a4f282
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
This also separates IRQ_PRI into one for DW and one
for QMSI, to follow the convention of every other
drivers.
Change-Id: I338f819f71c18fa9e17015e8a588a3d0207350c6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ic73783189db57059d2b7f3727e4802e1b2e27931
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifdbb5e3a997795ef577350d88f8cb06877eb6463
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib8158f00a6c6616360ddbcf63981f1a85911c1b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch extends the i2c shim driver so it supports the 'default
configuration' infrastructure which enables the user to specify a
default configuration for the I2C device. The default configuration
is set during driver initialization.
This patch also changes Quark SE and D2000 Kconfig.defconfig files so
the i2c default configuration is set to '0x12' which means standard
bus speed, 7-bit addressing and master mode. This is the same value
used when DW driver is selected, by the way.
Change-Id: I06e0dc3c29e8da2f3317db5bef285177f2e92c9a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Remove those kconfig options that are SoC specific, and should not be
configurable via kconfig.
Change-Id: Ia62888838877da4627419bd36c261d5254761acd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
These interrupt settings are SOC specific. So, move them to the
SOC level of Kconfig.
As IRQ priority is fixed in D2000, changed the value to 0 to
make it consistent with what other shim drivers are using.
Change-Id: Id20bed46c478a7555ae976e3a3063ba2cb099788
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This is hardware design so there is no need for it to be
configurable in kconfig.
Change-Id: Iff162f330aae8ef9a7139b6e7ed9bfa87f26189a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IRQ triggering condition should be specified by SoC as it is
a decision for hardware design. This should not be configurable
in kconfig.
The default is to be triggered on rising edge, just as the same
old kconfig did.
Change-Id: If59d88a30711eb8e03d9cc4f409055cefe1995c5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves those kconfig options which should be declared in
SoC or board header files instead. These are the one
that are tied to SoC or board and there is no need
for them to be configurable in kconfig.
Change-Id: I243d634f1a4a11dc8dc3530d95f93371015492b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: Iab10655c6fc6f17c0c6dd49cb7a4e74fabcf852c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: I3a51b35e633dc7b1b841e9fa504bf0cfc0d4d575
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Changed names of Kconfig flags, variables, functions, files and
return codes consistent with names used in the RFC. Updated
relevant comments to match the changes.
Origin: Original
Change-Id: Ie7941032d7ad7af61fc02928f74538745e7966e8
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch replaces all occurrences of DEV_* codes by errno.h codes at
the arch layer.
Change-Id: I1a1ab6d0481f3660ad032e2690d2577245fe1f34
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch fixes the QMSI UART shim driver so we are able to use it in
Quark D2000 based platforms. Differently from Quark SE, the peripheral
clock gate bit (CLK_PERIPH_CLK) is not enabled by default in Quark
D2000. We have to explicitly set this bit in order to properly initialize
the device.
Since this drivers is now properly working on Quark D2000, this patch
also sets the QMSI driver default options in arch/x86/soc/quark_d2000/
Kconfig.
Change-Id: I817b7703554be162ac628dcd8d3d07512b9eb3f5
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
() Moves the Quark SE clock control into its submenu.
() Fixes the dependencies in the SoC default Kconfig
so the options are not displayed out of place in
menuconfig.
Change-Id: Ifdf06242be8ceed03c2c657c942875a5a7f2750e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
These options should be selected by individual SoC automatically,
and should not be visible options. Or else it would be possible to
select Quark SoCs and telling Kconfig it is from Atom family (which
is incorrect).
Change-Id: I17a6cf713378333e0e7942aa49b381b5eb9526b5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When building with IAMCU, make sure we set the soft-float, otherwise
build would fail with unsupported instruction errors.
JIRA: ZEP-103
Change-Id: I7a5f107a2df50799a7f6dd4aba36c1a977c1461d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This creates the QMSI comparator driver which is simply a shim driver
based on the comparator driver provided by QMSI BSP.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_AIO_COMPARATOR=y
CONFIG_AIO_QMSI_COMPARATOR=y
Origin of the file: Original
Change-Id: Iad01cb80f7bb1eff1710cd76cd0afeb70c311e04
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This patch extends the UART QMSI driver so it supports the IRQ APIs from
include/uart.h. The IRQ APIs are enabled by the 'CONFIG_UART_INTERRUPT_
DRIVEN' option.
Differently from others APIs such as I2C and SPI, the UART API is very
low level. For that reason, the IRQ facilities (e.g. irq based transfers)
from the QMSI driver are not useful to the shim driver at the moment. In
order to implement the IRQ APIs we rely on UART registers defined by QMSI.
QMSI UART header is missing some macro definitions from IRR register so
we define them in the shim driver.
Since the IRQ trigger condition is not configurable in the QMSI shim
driver, this patch also changes drivers/serial/Kconfig so the "UART
IRQ Trigger Condition" choice doesn't appear on the menu if the QMSI
driver is selected.
Change-Id: Idf9a0f6a47af2a550a31f474d721068dca989713
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the QMSI UART driver which is simply a shim driver
based on UART driver provided by QMSI BSP.
This initial version implements only the mandatory APIs 'poll_in',
'poll_out' and 'err_check' which are required by trivial sample apps and
by output functionality from the console driver. The remaining APIs will
be implemented by up coming patches. The driver supports only 115200 baud
rate at the moment.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_SERIAL=y
CONFIG_UART_QMSI=y
This driver has been tested with Quark SE Devboard so this patch also
adds its platform-specific default configuration options to 'arch/x86/
soc/quark_se/Kconfig'.
Change-Id: Ibde1825d4b0349a376a8e7d91cc9de306946b62f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the macro UART_IOAPIC_FLAGS from Quark SE and D2000
soc.h since it is not used anywhere in the code.
Change-Id: I0fd42fac2f02e8617bd92c73c1a0354ef2d7a71a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Remove CPU_MIGHT_SUPPORT_CLFLUSH as excessive.
Removal the flag requires adding per-SoC cnfiguration,
as some Quark models support clflush instruction, but
some do not, even on compiler level.
Change-Id: I655cba00c629db55d1813c199a2fe08b2d60ef4f
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clockgating was disabled for RTC and disabling RTC had no
effect on Quark SE boards.
Change-Id: I67448d5582a206fc7a68d763d504e9f743043b53
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
ia32/soc.h is only used by QEMU, but QEMU's INTx routing does not follow
the "standard design consideration".
Instead, the pins are swizzled based on the PCI slot. They are then
routed to IRQs based on the PIIX PIRQ configuration.
For simplicity use hard-coded values for the PIIX PIRQ configuration,
though it may be desirable in the future to determine these dynamically.
Also change the number of PCI buses to 1 and remove irrelevant comments.
Change-Id: I1592009a43dd8a9c5a7c54788fba52f14687ba35
Signed-off-by: Ido Yariv <ido@wizery.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/i2c/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: If3c260b9a2fa095de47a99eb7fa5b947efefe9b1
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/spi/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: Ic992749b3210ed8a2e454edece41ceca5edbaf2e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/gpio/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: Id00f7907fa55025011dabce6e282a9623be23831
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch fixes the QMSI SPI shim driver so we are able to use it in
Quark D2000 based platforms. The only change required to enable this
driver is an #if guard in spi_qmsi_init() because the macro QM_SPI_MST_1
and the function qm_spi_master_1_isr are not defined in QMSI headers
from Quark D2000.
Since this drivers is now properly working on Quark D2000, this patch
also sets the QMSI driver default options in arch/x86/soc/quark_d2000/
Kconfig.
Change-Id: Ic6e2f7f5a2c3f350ddf360b23ffab6b812948572
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/watchdog/Kconfig because 1) most
of the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig (e.g. arch/x86/soc/quark_d2000/Kconfig).
For Quark D2000, the IRQ priority options (WDT_DW_IRQ_PRI and WDT_QMSI_
IRQ_PRI) values are set to '0' since the priority information is ignored
by the interrupt registering system (the interrupt vectors are fixed in
this SoC).
Change-Id: I8f36c0f0e56211cdee3f2c6fc90c7dcac0a1b5aa
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/rtc/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig (e.g. arch/x86/soc/quark_d2000/Kconfig).
For Quark D2000, the RTC_IRQ_PRI default value is set to '0' since the
priority information is ignored by the interrupt registering system
(the interrupt vectors are fixed in this SoC).
Change-Id: I70de889cfd22e65f0e7acf7e57ddc6439f028394
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The name already set by the driver's Kconfig is correct, so overriding
it only causes confusion.
Change-Id: Ia6405786fdfdf103c922517c8140a07a9de387e0
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This patch fixes the GPIO QMSI shim driver so we are able to use it in
Quark D2000 based platforms. To enable this driver we have to add a few
#if guards because some macros and functions (e.g. QM_AON_GPIO_0 and
qm_aon_gpio_isr_0) are not defined in QMSI headers from Quark D2000
(this SoC doesn't support the Always-On GPIO controller).
This patch also adds the QMSI driver default options to arch/x86/soc/
quark_d2000/Kconfig.
Change-Id: Ia16a345e1de3008f167ed66f891834607c05f4a2
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This adds support to the AON GPIO controller using the QMSI driver.
In order to enable it, the following configuration options must be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="PATH TO LIBQMSI"
CONFIG_GPIO_QMSI=y
CONFIG_GPIO_QMSI_AON=y
Change-Id: I5a1a232d97741ad7fdbf40d8aea5a835e5b4e724
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds a NULL check against the reset vector for ARC.
If the reset vector is null, do not start the ARC core
as there is nothing to execute, and will probably cause
the whole SoC to stall.
Change-Id: I78d77b3e5940a205e05c13369f889cf9c5955487
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch changes both Quark SE and D2000 Kconfig files to enable the
WDT_DW driver by default if the WATCHDOG is enabled. This way, we keep
it consistent with the approach we already follow for others peripheral
drivers (GPIO, I2C, SPI).
Change-Id: I9d8b81c0e659b1408137deb71e33dacf6d4108c2
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch changes both Quark SE and D2000 Kconfig files to enable the
RTC_DW driver by default if the RTC is enabled. This way, we keep it
consistent with the approach we already follow for others peripheral
drivers (GPIO, I2C, SPI).
Change-Id: I4910e501c105b6218d046080c47b1e7a42eced92
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch fixes the QMSI I2C shim driver so we are able to use it in
Quark D2000 based platforms. The only change required to enable this
driver is an #if guard in i2c_qmsi_init() because the macro QM_I2C_1
is not defined in QMSI headers from Quark D2000.
Since this drivers is now properly tested with Quark D2000, this patch
sets the QMSI driver default options in arch/x86/soc/quark_d2000/Kconfig.
It also adds the wiring information required to test the i2c_lsm9ds0
sample app in the Quark D2000 CRB.
Change-Id: I4be03c09304da5a66ac663e48b1d72225eb5651d
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
In case the I2C_QMSI driver is selected by the user, enable both I2C
contollers by default. This is the default behavior for I2C_DW driver
as well.
Change-Id: If3dc8eb0a266fde7f598f7b12370e5be903aafed
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Always use braces, even on one-line code blocks.
Change-Id: Ic9e60db7f851d2fbee5bfd79cd810df23c0c5db0
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Making pipe driver configuration for quark_se makes no sense for the
board. First it simply wrong since IRQs for serial are 5 and 6 and
when using PIPE care should be taken to allocate right way serial and
Bluetooth for the given UARTs.
Change-Id: I4cb3227a8be34fbfa089a457e6d9977e4adcfd19
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
QUARK_SE_IPM_CONSOLE_RING_BUF_SIZE32 symbol must be editable through
configuration menus and configuration snippets (QA request).
Adding a title for the kconfig symbol makes it editable.
Change-Id: Id0147a50d94033e1392327935bcbfbdb5a9eedd8
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This driver uses the QMSI library and mostly translates calls from the
Zephyr API to QMSI ones.
This driver conflicts with the native driver implemenation. In order to
enable it, you must set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="PATH_TO_QMSI"
CONFIG_SPI_QMSI=y
CONFIG_SPI_QMSI_PORT_0=y
CONFIG_SPI_QMSI_PORT_1=y
Missing:
- Support for using a GPIO pin as Chip Select;
Change-Id: I0d8eca88a2a803b6b3604f396f874313fe90753c
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I458afca5feb9be5de8dcae559d6dcac3c6d6a2a7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Due to an issue with the interrupt-based transfer API from QMSI driver,
the 'transfer' callback from the shim driver (i2c_qmsi_transfer) is
implemented with polling APIs. This is not ideal because we are not able
to sleep the current thread (so another task can be scheduled in) while
the i2c operation is carried out.
The interrupt issue with the QMSI driver has been solved then this patch
fixes the shim driver so it uses the interrupt-based API and adds extra
code to handle the thread synchronization.
Finally, this patch also moves all 'struct device' related definitions
from the bottom to the top of the i2c_qmsi.c file so the DEVICE_GET
macro can be used in transfer_complete() and removes the init.h include
since it is not needed anymore.
Change-Id: I7ef7ce4cea6fcc939e310e5fe12c406645f6a16e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
IRQAGENT3 is initialized explicitly, but IRQAGENT0 isn't and its value
is based on the value the BIOS or bootloader had set before. Fix this by
explicitly initializing IRQAGENT0, and swizzle the IRQs to reduce
conflicts.
Update the pci_pin2irq function to accommodate for these changes.
Also remove pci_irq2pin function since it is unused.
Change-Id: I7b1dfc7659ab227fe66711a3af5a1f34fd4a7972
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
To debug PCI drivers on QEMU, it may be desired to enable CONFIG_PCI for
QEMU targets. Since the PCI driver requires a SOC pin2irq translation
function, add such function to IA32's SOC header file.
Change-Id: Icf6f88aa14ae29d70fe12dc80a708e6a2e992ba8
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Move BLE configuration to board and enable GPIO for NBLE.
Change-Id: I99c309656430936edf6766fc99fe83b011801bb4
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds basic support for communication with Nordic BLE (NBLE) chip
connected to UART.
Change-Id: I3651e291ec18805a63ecd3d240dce62273e3c498
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
It's not a function and requires all its arguments to be build-time
constants. Make this more obvious to the end user to ease confusion.
Change-Id: I64107cf4d9db9f0e853026ce78e477060570fe6f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Mostly SoC initialization and some kernel subsystems, but also some
device drivers like the interrupt controllers.
Change-Id: I8dc1844c33acd877c075b6b03558fdca6f87500b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Introduce the GPIO QMSI-based implementation. This is basically a
shim layer that implement's Zephyr's GPIO APIs on top of QMSI drivers.
This is an alternative driver that conflicts with the previous
GPIO_DW implementation. In order to enable it you must set:
- CONFIG_GPIO=n
- CONFIG_GPIO_QMSI=y
- CONFIG_GPIO_0=y
- CONFIG_QMSI_DRIVERS=y
- CONFIG_QMSI_INTALL_PATH="PATH_TO_QMSI"
Note that this driver currently only supports one controller instance,
GPIO_0. It is implemented this way due to a limitation from the current
version of QMSI. QMSI versions later than 1.0 doesn't have this
limitation.
Missing:
- support multiple controller instances (gpio_0, gpio_1, etc);
- enable level triggered interrupts in sync with system clock,
through setting INT_CLOCK_SYNC properly.
Change-Id: Ib61b153dae9741806a9a31d7dc1f82b96d000fbe
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
On Quark SE, SPI might require GPIO to be ready before hand, to emulate
CS, thus providing an option to tweak the intialization priority for SPI
DW driver.
Change-Id: Ifa373948ac8227bf6e4ed1113bcb4dc9139b6663
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Quarks SE owns a GPIO controller which is always on (so not clock-gated)
thus providing it base address, the pins it handles etc...
Change-Id: Ifceb7cb74e763a91130d615ba19756ddcbe97a23
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is valid only for Quark SE and Quark SE SS, where it requires to
unmask the interrupt for each specific controller. Thus making the
function generic, using the parameter as the specific mask base address.
Change-Id: Iea0a412b8d94a1ab5e1f3e339eaf632eacee5797
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The original value of 128 was selected more or less randomly, and
isn't sufficiently large enough for QA needs.
Change-Id: I8a9fcc86d6b5fa7dc5ba05896c62f7dd608f9ed2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This reverts commit 778d5b11c5327be4b40c7745e9beaecfd6327e13.
This patch has been identified as breaking the build when trying
to manually build non-x86 applications.
Change-Id: I1857745049dfef7193de58737108314b7aae01c5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These are not (yet) used anywhere and generate unnecessary warnings.
Just remove them.
Change-Id: Ibae472c4a639466c221cdc354232780db04e963e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define configuration for Nordic chip connected to UART0.
Change-Id: Ia6007def747932e5f9fbd57f1ea8005892a2f793
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I0f77cffe7a139f8b2620935094437d0dfd160dfe
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Kbuild system first looks for a Kbuild file, then it looks for
a make file.
Use the Kbuild for object building and leave the Makefile for definding
build options and compiler flags and other SoC related defines.
Change-Id: I0be59bb5ae02a29108a188efbd6f14dcdb7de4ee
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Currently, if we disable I2C_DW through 'menuconfig', I2C_DW_0* and
I2C_DW_1* options are not disabled even if they depend on I2C_DW
option. This makes the menuconfig confusing and we end up with the
wrong config set in .config file:
...
CONFIG_I2C_DW is not set
CONFIG_I2C_DW_0=y
...
CONFIG_I2C_DW_1=y
...
This patch fixes this issue by surrounding the I2C_DW_0* and I2C_DW_1*
options with 'if I2C_DW'.
Change-Id: I7e949b066425bca2533f8b84b9ea7b1915369ff0
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch introduces the 'QMSI RTC device driver' which is simply a shim
driver based on RTC driver provided by QMSI BSP.
Some config options are independent of the driver implementation used,
so use a consistent name for them. In this case RTC Interrupt number and
Priority use the same config options for both the QMSI and DesignWare
drivers.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_RTC=y
CONFIG_RTC_QMSI=y
Change-Id: I48292406e5472e5786f3b9abbeb71016a273bfec
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This enables building with the iamcu variant of the x86 compiler
and enabled using the IAMCU ABIs.
Change-Id: Idf71251898e250b8df73c065462c93c289879fe2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are a few bits missing on enabling I2C controller on
quark_d2000_crb. This adds the missing bits.
Change-Id: I05bbe8367a9e69962db573d496f1f9f0167ba597
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART on Quark SE and D2000 supports fractional clock divider.
It is used to limit frequency error for supported baud rates.
Change-Id: I1f39a95db09f4a5a4116edc700a10e4b9ecfa2bd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Johan Hedberg