This will be used for both 32-bit and 64-bit mode.
This header gets pulled in by x86's arch/cpu.h, so put
it in include/arch/x86/.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add qemu_x86_long board (with CONFIG_X86_LONGMODE=y) for testing.
This requires adding support to soc/ia32 for long mode (trivial),
and adding a quick 64- to 32-bit ELF conversion before invoking
QEMU, which apparently doesn't like 64-bit kernel files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
XIP support in x86 was something of a mess. This
patch does the following:
- Generic ia32 SOC no longer defines a "flash" region
as generic X86 devices don't have a microcontroller-
like concept of flash. The same has been done for apollo_lake.
- Generic ia32 and apollo_lake SOCs starts memory at 1MB.
- Generic ia32 SOC may optionally have CONFIG_XIP enabled.
The board definition must provide a flash region definition
that gets exposed as DT_PHYS_LOAD_ADDR.
- Fixed definitions for RAM/ROM source addresses in ia32's
linker.ld when XIP is turned off.
- Support for enabling XIP on apollo_lake SOC removed, there's
no use-case.
- acrn and gpmrb boards have flash and XIP related definitions
removed.
- qemu_x86 has a fake flash region added, immediately after system
RAM, for use when XIP is enabled. This used to be in the ia32 SOC.
However, the default for qemu_x86 is to now have XIP disabled.
- Fixed tests/kernel/xip to run by default on boards that enable
XIP by default, plus an additional test to exercise XIP on
qemu_x86 (which supports it but has XIP switched off by default)
The overall effect of this patch is to:
- Remove XIP configuration for SOC/boards where it does not make
any sense to have it
- Support testing XIP on qemu_x86 via tests/kernel/xip, but leave
it off by default for other tests, to ensure it doesn't bit-rot
and that the system works in both scenarios.
- XIP remains an available feature for boards that need it.
Fixes: #18956
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Removes very complex boot-time generation of page tables
with a much simpler runtime generation of them at bootup.
For those x86 boards that enable the MMU in the defconfig,
set the number of page pool pages appropriately.
The MMU_RUNTIME_* flags have been removed. They were an
artifact of the old page table generation and did not
correspond to any hardware state.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The only use of the BOOTLOADER_UNKNOWN config option is on x86, where
it controls whether a multiboot header is embedded in the output.
This patch renames the option to be more descriptive, and makes it
an x86-specific option, rather than a Zephyr top-level option.
This also enables X86_MULTIBOOT by default, since the header only
occupies 12-16 bytes of memory and is (almost always) harmless.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Previous rename from CONFIG_* to DT_* left a few remaining
CONFIG_*. So rename them manually now.
Fix#13753
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds a driver for Intel PRO/1000 Gigabit Ethernet controller.
The driver currently supports only a single instance of the NIC.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
We get several warnings of the form:
Warning (unit_address_format): /soc/uart@000003f8:
unit name should not have leading 0s
Fix these by remove the leading 0s.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Andrew Boie