Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added architecture specific support for memory domain destroy
and remove partition for arm and nxp. An optimized version of
remove partition was also added.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Because the mcux shim drivers will soon depend on a clock control
interface, enable the mcux sim clock control driver by default on all
Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Currently this is defined as a k_thread_stack_t pointer.
However this isn't correct, stacks are defined as arrays. Extern
references to k_thread_stack_t doesn't work properly as the compiler
treats it as a pointer to the stack array and not the array itself.
Declaring as an unsized array of k_thread_stack_t doesn't work
well either. The least amount of confusion is to leave out the
pointer/array status completely, use pointers for function prototypes,
and define K_THREAD_STACK_EXTERN() to properly create an extern
reference.
The definitions for all functions and struct that use
k_thread_stack_t need to be updated, but code that uses them should
be unchanged.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the define generated by the DTS instead of using the FLASH_ALIGN
alias. The latter is an internal mcuboot name. We shouldn't need it in
Zephyr itself.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This workaround fixes the issue that, after pin reset, RESETREAS bits
other than RESETPIN might also be set.
The workaround was added to both nRF52832 and nRF52840 SoCs.
Signed-off-by: Thiago Silveira <thiago@exati.com.br>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add the following application-facing memory domain APIs:
k_mem_domain_init() - to initialize a memory domain
k_mem_domain_destroy() - to destroy a memory domain
k_mem_domain_add_partition() - to add a partition into a domain
k_mem_domain_remove_partition() - to remove a partition from a domain
k_mem_domain_add_thread() - to add a thread into a domain
k_mem_domain_remove_thread() - to remove a thread from a domain
A memory domain would contain some number of memory partitions.
A memory partition is a memory region (might be RAM, peripheral
registers, flash...) with specific attributes (access permission,
e.g. privileged read/write, unprivileged read-only, execute never...).
Memory partitions would be defined by set of MPU regions or MMU tables
underneath.
A thread could only belong to a single memory domain any point in time
but a memory domain could contain multiple threads.
Threads in the same memory domain would have the same access permission
to the memory partitions belong to the memory domain.
The memory domain APIs are used by unprivileged threads to share data
to the threads in the same memory and protect sensitive data from
threads outside their domain. It is not only for improving the security
but also useful for debugging (unexpected access would cause exception).
Jira: ZEP-2281
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
SoCs outside the Kinetis family can have the TRNG module, so move the
HAS_TRNG config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the RNGA module, so move the
HAS_RNGA config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the ADC16 module, so move the
HAS_ADC16 config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
mcuboot_constraints.h had FLASH information related to the SoC that
should be maintained as part of the SoC and not in the subsystem. Also
fixed Makefiles to check for IMG_UTIL Kconfig and not MCUBOOT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
stm32f417xe and stm32f417xg have been introduced with 2
different defconfig files. Since same code is declared
in both files, mutualize declarations in a single file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The enumerations stm32{f3,f4}x_pin_config_mode aren't used any
more. This patch removes them.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In various places, a private _thread_entry_t, or the full prototype
were being used. Be consistent and use the same typedef everywhere.
Signen-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indenting preprocessor directives reduces the code readability, because
it make preprocessor directives harder to spot.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Previously, this was only done if an essential thread self-exited,
and was a runtime check that generated a kernel panic.
Now if any thread has k_thread_abort() called on it, and that thread
is essential to the system operation, this check is made. It is now
an assertion.
_NANO_ERR_INVALID_TASK_EXIT checks and printouts removed since this
is now an assertion.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In benchmark test (test_info) while making function call regs
r0 - r4 are modified into called function. Due to this value
inside r3 is getting lost.
This patch saves and restore the value in r0-r4 regs while making
function calls from assembly language.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The API/Variable names in timing_info looks very speicific to
platform (like systick etc), whereas these variabled are used
across platforms (nrf/arm/quark).
So this patch :-
1. changing API/Variable names to generic one.
2. Creating some of Macros whose implimentation is platform
depenent.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This patch fixes a couple of issues with the stack guard size and
properly constructs the STACK_ALIGN and STACK_ALIGN_SIZE definitions.
The ARM AAPCS requires that the stack pointers be 8 byte aligned. The
STACK_ALIGN_SIZE definition is meant to contain the stack pointer
alignment requirements. This is the required alignment at public API
boundaries (ie stack frames).
The STACK_ALIGN definition is the required alignment for the start
address for stack buffer storage. STACK_ALIGN is used to validate
the allocation sizes for stack buffers.
The MPU_GUARD_ALIGN_AND_SIZE definition is the minimum alignment and
size for the MPU. The minimum size and alignment just so happen to be
32 bytes for vanilla ARM MPU implementations.
When defining stack buffers, the stack guard alignment requirements
must be taken into consideration when allocating the stack memory.
The __align() must be filled in with either STACK_ALIGN_SIZE or the
align/size of the MPU stack guard. The align/size for the guard region
will be 0 when CONFIG_MPU_STACK_GUARD is not set, and 32 bytes when it
is.
The _ARCH_THREAD_STACK_XXXXXX APIs need to know the minimum alignment
requirements for the stack buffer memory and the stack guard size to
correctly allocate and reference the stack memory. This is reflected
in the macros with the use of the STACK_ALIGN definition and the
MPU_GUARD_ALIGN_AND_SIZE definition.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch removes the redundant stack alignment check being done. The
stack definition macros enforce the alignment requirements via the
__align() directives.
In addition, fix the rounding down of the psp to be correct. The
actual initial stack pointer is the end of the stack minus the size of
the __esf structure. Rounding down after the subtraction will get us
to the correct offset.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Anas Nashif