With most boards there's no simple way to get access to the HCI
traffic. Simultaneously these boards only have one external UART for
the console. This patch introduces a protocol which combines both
normal logs and HCI logs over a single binary protocol sent over the
console UART.
The protocol is modeled based on the btsnoop/monitor protocols used by
BlueZ, and the first tool that's able to decode this is btmon from
BlueZ ("btmon --tty <tty>").
For platforms with two or more external UARTs it is still possible to
use CONFIG_UART_CONSOLE as long as the UART devices used are
different, however on platforms with a single external UART
UART_CONSOLE should be disabled if BLUETOOTH_DEBUG_MONITOR is enabled
(in this case printk/printf get encoded to the monitor protocol).
Origin: Original
Change-Id: I9d3997c7a06fe48e7decb212b2ac9bd8b8f9b74c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: Ia252958d205e0100d1b92e2a12d4c22411bc94b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Johan Hedberg