Avoids confusion with .gitignore rules, which were inadequate to
cover all the places where these files are found. At least in
VIM, these files are now syntax highlighted correctly.
Change-Id: I23810b0ed34129320cc2760e19ed1a610afe039e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The clock_init() is always called so this can be inlined.
This saves 32 bytes of ROM space compared to non-inlined version.
Change-Id: I1b95142da4c22f4b7fc7f7f6210503d90cf65cc9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This also enables GPIO on ATMEL SAM3 when GPIO is set.
Change-Id: I4125af4910d57bed98b0ee4967fb696e3f345e67
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Changed names of Kconfig flags, variables, functions, files and
return codes consistent with names used in the RFC. Updated
relevant comments to match the changes.
Origin: Original
Change-Id: Ie7941032d7ad7af61fc02928f74538745e7966e8
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The nmi_on_reset.S functions are used by all ARM platforms. It
makes no sense to repeat the same code for all platforms. Moving
the code from each SOC implementation to arch/arm/core.
The same treatment for the NMI_INIT() macro. Moving it from a per
SOC implementation to the include/arch/arm/cortex_m/nmi.h.
Change-Id: I574d8880a44046cc7b9e1b635e80d6e83657b8c1
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
This reverts commit 3f6884902b.
This commit does not work as intended: the part in arch/arm/Makefile
gets ignored and -mcpu=cortex-m3/4 does not get passed to gcc. It seems
that the zephyr toolchain does not care, but the vxworks assembler
chokes if it is missing, and thinks the CPU does not support thumb ISA
Change-Id: I14d11d3e22dac4952bdab3eb9e2d1c36b1a686c2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
We don't support hard-coding vectors in this table anymore.
If someone really wants to do this, they can set
IRQ_VECTOR_TABLE_CUSTOM and define their own.
Change-Id: I45f49782ba5fefb0a02eab02ec96efd0019bc6d5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Currently the build system has hardcoded values for the -march/-mcpu
which identify what architecture should be used when compiling ARM code.
For processors such as the STM32 this will need to be defined by a per
SOC process.
Change-Id: Ia8158cd687d8d0432ea420e204bb2bc67d33a054
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Adds the driver to utilize the I2C/TWI interface on Atmel SAM3
family processors for I2C communication.
Note that this currently only supports master mode. Limited
testing has been done using the Fujitsu FRAM sample app.
Change-Id: Ibdb8277e47dd9450b49a66a95421eb1ffb1c4eb4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds the struct to describe PDC (Peripheral DMA Controller).
The PDC is being used by peripherals to initiate DMA
transfers.
Change-Id: Ida2a20810c4f2ef972e9669c45e22da07c1576ab
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I458afca5feb9be5de8dcae559d6dcac3c6d6a2a7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The default Kconfig option is missing a condition for the SRAM
base address on SAM3X8E. Add it back so the correct default
can be used.
Change-Id: Ib4103366f693648c76630cbbd71ca98109381d5c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The PIO controllers on Atmel SAM3 family processors can be
used for GPIOs, so this is the driver.
Change-Id: I3d5712f3a0a71025b820ca1c08dd767ee1e136d8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Mostly SoC initialization and some kernel subsystems, but also some
device drivers like the interrupt controllers.
Change-Id: I8dc1844c33acd877c075b6b03558fdca6f87500b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds initial support for Atmel SAM3X8E processor, which is
based on ARM Cortex-M3. The SAM3X8E is being used on Arduino Due.
Change-Id: I199efcf29629f9ebacad474e5edc91bc3757f613
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Anas Nashif