These MCUs have 32Kbytes of Flash and 8Kbytes of RAM. They are still
able to run a number of samples.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
The number of capture/compare registers available on a peripheral
should be exposed in devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The nRF5340 (P)DK is equipped with the MX25R64 flash memory. Add a dts
node for that chip in the board definition as well as the missing QSPI
node in the nRF5340 SoC definition.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Reworks the mcux ethernet driver to use DT_INST_FOREACH_STATUS_OKAY and
eliminate a lot of duplicate code between instance 0 and instance 1.
Renames the ERR_MISC interrupt to ERR due to an issue with the
underscore in the device tree preprocessor macros.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors nxp i.mx, kinetis, and lpc soc-level device trees to use
DT_SIZE_K and DT_SIZE_M macros to define internal memory sizes. This is
self documenting and easier to read.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
MSI-X PVM feature requires snoop interrupt for tracking configuration
space register (msix_cap) update and PCIe PMON lite interrupt for
tracking MSI-X table update. Add both the interrupts for Viper M7 DT.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
The DMA channel number used for the DMA transfer can now
be specified from the device tree config files
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This defines the TRNG for EFM32GG11 and enables it for trng0
in the dts for the matching development kits.
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
This defines wdog0 and wdog1 for the EFM32GG11 MCU and enables wdog0
in the dts for the matching development kits.
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
While the STM32H7 features a special dual mode operation for ADC1 and
ADC2, the register specified for adc1_2 node was actually the one for
ADC1 in normal single mode operation.
This commit fixes register for dual mode and adds adc1 and adc1 nodes.
Signed-off-by: Martin Jäger <martin@libre.solar>
Commit ac31c4e458 updated the mcux
ethernet driver to get the ethernet peripheral base address from device
tree instead of an nxp hal preprocessor macro. This exposed an error in
the k6x device tree and caused a runtime assertion in networking
applications on the frdm_k64f board:
ASSERTION FAIL [instance < (sizeof(s_enetBases) / sizeof((s_enetBases)[0]))] @ WEST_TOPDIR/modules/hal/nxp/mcux/drivers/kinetis/fsl_enet.c:323
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In npcx7 series, there're 8 Pulse Width Modulator (PWM) modules and each
one support generating a single 16-bit PWM output. A 16-bit clock
prescaler (PRSCn) and a 16-bit counter (CTRn) determine the cycle time,
the minimal possible pulse width, and the duty-cycle steps.
Beside introducing pwm driver for Nuvoton NPCX series, this CL also
includes:
1. Add PWM device tree declarations.
2. Zephyr PWM api implementation.
3. Add aliases in npcx7m6fb_evb board device tree file for supporting
samples/basic/blinky_pwm application and pwm test suites
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Only difference compared to existing Xe variant is less flash memory.
Existing nodes for DAC were moved up one level to stm32g474.dtsi
Signed-off-by: Martin Jäger <martin@libre.solar>
Change default pinmux of functional pads to GPIOs. It includes:
1. PIN96.A0.A2.A4 - If internal flash is supported
2. PIND2.00 - Default PSL inputs
3. PIN31.30.27.26.25.24.23.22 - Keyboard inputs
4. PIN21.20.17.16.15.14.13.12.11.10.07.06.05.04.82.83.03.B1 - Keyboard
outputs
5. Add description for soc_pinctrl_mux_configure() usage.
It also fixed the typo and inverse mistakes in npcx7-alts-map.dtsi.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL adds more comments for each macro functions used for device tree
file for better explanations. It also changes all hex values in soc.c to
lower case.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL contains the drivers of NPCX Host Sub-Modules that serve as an
interface between the Host and Core domains. For most of them, the Host
can configure these modules via eSPI(Peripheral Channel)/LPC by
accessing 'Configuration and Control register Set' which IO base address
is 0x4E as default. And the interrupts in core domain help handling any
events from host side.
In this commit, we introduced six host sub-modules. It includes:
1. Keyboard and Mouse Controller (KBC) interface.
2. Power Management (PM) channels.
3. Shared Memory mechanism (SHM).
4. Core Access to Host Modules (C2H).
5. Mobile System Wake-Up functions (MSWC).
6. Serial Port (Legacy UART)
The tasks in application layer such as 8042, ACPI and host command can
cooperation with this driver by connecting api or callback functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
In npcx7 series, all of them support the Intel Enhanced Serial
Peripheral Interface (eSPI) Revision 1.0. This specification provides a
path for migrating host sub-devices via LPC to a lower pin count, higher
bandwidth bus. In addition to Host communication via the peripheral
channel, it provides virtual wires support, out-of-band communication,
and device mastering option over the Chipset SPI flash.
Becisdes introducing eSPI device in npcx7, this CL also includes:
1. Add eSPI device tree declarations.
2. Add npcx7-espi-vws-map.dtsi to present the relationship between eSPI
Virtual-Wire signals, eSPI registers, and wake-up input sources.
3. Zephyr eSPI api implementation.
4, Add OOB (Out of Band tunneled SMBus) support.
5. Add configuration files for eSPI test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
stm32f1 series pin controller IP is not compatible with other stm32
series.
Set the dedicated st,stm32f1-pinctrl compatible for pinctrl node.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename compatible st,stm32-pinmux to st,stm32-pinctrl to better
reflect the nature of upcoming child nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L151xC SoC differs from other L1 SoCs in RAM (32KiB) and
flash (256KiB) size, and amount of interrupts (57, see STM32Cube).
Devicetree and Kconfig support.
Signed-off-by: Noelle Clement <noelleclement@hotmail.com>
Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
* Add ADC2 and ADC3 to the F103xE definition.
* Add a dtsi file for the F103xG based on the F103xE.
The F103xG has 1 MB of flash, 96 KB of RAM, and additional timers
TIM9/10/11/12/13/14.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
update rt6xx series sram mapping to skip 0x180000,
reserved for DSP usage.
this fixes tests/subsys/debug/coredump for this board
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The sam4l pinctrl contains two entries with wrong values. Fix the
typo to create valid pinctrl map.
Fixes#28538.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Change #28199 introduced systick configuration from device tree.
For now this should not be used on platforms that support alternate
tick source, as this is the case on l4 and wb series with LPTIM.
Until dts allows to configure lptim from dts, keep systick disabled
by default on these platforms.
Fixes#28280
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use setting from devicetree to drive the default setting for
CORTEX_M_SYSTICK. We update the dts files to default systick to be
enabled since the major of cortex-m platforms utilize it by default
(except on Nordic SoCs, TI CC13x2/CC26x2 and MEC1501 in which we
default to disabled).
Fixes#25299
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for UARTs 3-6 to the stm32f030xc SoC. These additional UARTs
share a single interrupt line, so only one may be enabled at a time.
Signed-off-by: Brian Kubisiak <brian@kubisiak.com>
This CL configures the UART wake-up event triggered from a falling edge
(START condition) on CR_SIN pin. It also includes:
1. Introduce wui_maps property in yaml file to present relationship
between Wake-Up Input (WUI) and UART device.
2. Implement wake-up mechanism by MIWU api functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add gpio support for Nuvoton NPCX series. This CL includes:
1. Add GPIO device tree declarations.
2. Introduce wui_maps property in yaml file to present relationship
between Wake-Up
Input (WUI) and 8 IOs belong to the device.
3. Zephyr GPIO api implementation.
4. GPIO callback functions implementation with MIWU api functions.
5. Overlay file for gpio basic tests
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The device Multi-Input Wake-Up Unit (MIWU) supports the embedded
controller (EC) to exit 'Sleep' or 'Deep Sleep' power state which allows
chip has better power consumption. Also, it provides signal conditioning
such as 'Level' and 'Edge' trigger type and grouping of external
interrupt sources of NVIC. The NPCX series has three identical MIWU
modules: MIWU0, MIWU1, MIWU2. Together, they support a total of over 140
internal and/or external wake-up sources.
In this CL, we use device tree files to present the relationship bewteen
MIWU and the other devices in different npcx series. For npcx7 series,
it include:
1. npcx7-miwus-int-map.dtsi: it presents relationship between MIWU group
and NVIC interrupt in npcx7. Please notice it isn't 1-to-1 mapping.
2. npcx7-miwus-wui-map.dtsi: it presents relationship between input of
MIWU and its source device such as gpio, timer, eSPI VWs and so on.
This CL also includes:
1. Add MIWU device tree declarations.
2. MIWU api function declarations and implementation to configure signal
conditions and callback function mechanism. They can be be classified
into two types. One is for GPIO which connects original gpio callback
implemetation and the other is for generic devices such as timer,
eSPI, and so on.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Steven Daglish