Since introduction of #24374 this test fails on STM32 boards.
Due to 1Hz frequency of RTC used, the 'diff' could be 0.
But then 'counter_us_to_ticks(dev, processing_limit_us)' is also 0.
We should allow the equality in the assert.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert DT_RTC_0_NAME to DT_LABEL() references based on the compat being
defined in the build.
Introduce a set of macros that will generate a list of labels based on
compatible matches.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Test is checking if alarm handler is executed at request time or later.
However, validation did not take into account wrapping of the counter.
Fixed by taking into account case where counter wraps.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fixes test which did not take into account that counter may
wrap (nrf51 has 16bit timers) and was setting alarm to wrong
value. Error was not seen on platforms with higher top value.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The board name for the nRF52833 DK, so far known as nrf52833_pca10100,
is renamed to nrf52833dk_nrf52833. Its documentation and all
references to its name in the tree are updated accordingly.
Overlay and configuration files specific to this board are also
renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The board target for emulation of nRF52811 on nRF52840 DK, so far
known as nrf52811_pca10056, is renamed to nrf52840dk_nrf52811.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fixes a timeout failure on the frdm_k64f board.
test_short_relative_alarm iterates 100x through a 3 tick loop, but some
platforms like frdm_k64f have a 1 second counter tick period and
therefore need more time to finish this test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
test_single_shot_alarm_instance may fail due to not supported setting
of top_value in call to counter_set_top_value.
Modified to accept not supported case.
Fixes#21745
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Teardown may fail due to not supported setting of top_value.
Modified to accept not supported case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add a single counter API test case (not using callbacks) running in
user mode. Convert the existing test setup to use semaphores for
counting events to be able to utilize the same test setup and teardown
functionality in both user and supervisor mode tests.
Most of the counter API basic test suite still needs to run in
supervisor mode due the use of callback functions.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
On nRF platforms, Xtal LF clock source starts hundreds of milliseconds.
Until it is not started, test may fail due to wrong timing. Add initial
delay in the test for required clocks complete their start-up.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Refactors the mcux rtc driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
COUNTER_LOG_LEVEL (defined in
subsys/logging/Kconfig.template.log_config) is derived automatically and
has no prompt. Assignments have no effect on promptless symbols.
Set COUNTER_LOG_LEVEL_DBG=y instead, which corresponds to
COUNTER_LOG_LEVEL=4.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Some tests assume that the counters are always counting up
without regard to their capabilitiy bits. So fix the tests
if those counters are counting down.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Added tests which verifies that:
- driver will detect when absolute alarm is set too late.
- short relative alarm is supported
- canceled alarm is not triggering user callback
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Implemented latest extensions to the counter API related to
detection of alarms being set too late and short relative alarms.
Implementation could not be realized on nrfx_rtc driver thus
driver has been reimplemented based on nrf_rtc hal.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Application board.overlay files tend to be paired with
boards/board.conf files that extend the functionality of a board.
Move the overlay files to the same location as the config files that
they work with.
A few overlay files that are paired with a prj_board.conf file in the
application root directory are left in place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Flags in alarm configuration structure will allow further extention
without breaking API. Initially, existing absolute flag was added
as the only flag.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
move counter.h to drivers/counter.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit introduces new top_value setting configuration structure
with flag for controlling resetting of the counter during change of
top value.
Such change allows for #12068 implementation on hardware which
does not provide alarms.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Enable the counter capability in the board and add a .conf file for the
nRF52810 running on the PCA10040 board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds support for board: nrf52811_PCA10056.
The nRF52840 DK: PCA10056 is the recommend development kit, it emulates
the nRF52811, and can be used as a starting point for development
before moving over to a custom board.
Please note that this development kit does not support Bluetooth
Direction Finding. What is more it cannot be used with most of Arduino
shields because of PCA10056 PIN layout.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Exclude nucleo_f302r8 platform as the tests doesn't fit in flash size.
This is due to that fact that we pull in newlib for the STM32 counter
driver.
Fixes#15460
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix issue reported by coverity regarding using volatile
variables in zassert_equal macro.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Alexandre Bourdiol