Fixes#16739. Changed the STM32's SPI MISO/MOSI configurations in order
to reduce the power consumption by approximately 20uA per pin.
According to STM32's Application Notes on GPIO configuration for
low-power consumption, the input pins should be configured with internal
pull-up or pull-down resistor. If a pin is configured as a floating
input, and there is no signal present, the Schmitt trigger randomly
toggles between the logical levels induced by the external noise, thus
increasing the consumption.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
The i2c5 instance are used on arduino connector of
stm32mp157c-dk2.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
Add eSPI Microchip XEC driver
Include support for peripheral & virtual wires (channel 0-1)
OOB and flash support can be added in the future
Fix compilation error in pinmux driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This driver introduces pinmux configuration capabilities
using zephyr apis for XEC SOCs.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit adds pinmux defines for all the external ADC lines
supported by stm32. All defines are named after the datasheet of the
corresponding product lines.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Since STM32_OSPEEDR_VERY_HIGH_SPEED flag is required for all I2S_CK
pins, lets add this to the STM32F4 pinmux header and remove the
duplicates in board files. While we are at it, let's add the missing
pinmux definitions for I2S_2 also.
Fixes: #9028
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Reformat L4 pinmux to be consistent with other pinmux files,
and for a better reading.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Most of these are from source'ing a file within an 'if PINMUX', and then
adding another 'depends on PINMUX' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Converts the rv32m1 pinmux driver to use 'DT_' prefixed defines instead
of deprecated non-prefixed defines.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Tomasz Bursztyka