All the of the ITE it8xxx2 devicetree compatiables are of the form
ite,it8xxx2-<DEV>. However the PECI device was ite,peci-it8xxx2,
rename the compatiable to match the pattern used everywhere else.
Signed-off-by: Kumar Gala <galak@kernel.org>
Some files were missed during the migration. This patch adds the prefix
where missing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the sifive,clint0 compatible instead of "riscv,clint0" and remove
interrupt controller fields (clint compatible is used for its timer
registers). Refer to the Linux or previous commits for more context.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the sifive,clint0 compatible instead of "riscv,clint0" and remove
interrupt controller fields (clint compatible is used for its timer
registers). Refer to the Linux or previous commits for more context.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The CLINT (Core Local Interruptor) description was not aligned with
Linux. For example, there's no "riscv,clint0", but "sifive,clint0". The
peripheral is not described as an interrupt-controller either.
Ref. https://elixir.bootlin.com/linux/v5.18.14/source/arch/riscv/boot/
dts/starfive/jh7100.dtsi#L106
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After some analysis I found out that there's no machine timer provided
by the "riscv" vendor. There are some specs for the mtime/mtimecmp
registers (this is why we can have a single driver), but the actual
register layout or implementations differ amongst vendors. GD32 uses the
Nuclei implementation, named "system timer" in their documentation. This
patch aligns with vendor specs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
ITE EC chip it81202 and it81302 both have embedded integrated
pd module (support two usbpd ports), this is different from
standalone TCPC. To prevent cc pins leakage, we disable not
active ITE USBPD port cc modules, then cc pins can be used
as gpio if needed.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
The built-in USB serial peripheral is a virtual serial and does not
allow to be configured like a normal UART.
Removing the unused UART config parameters.
Also reducing initialization to single-instance only.
Signed-off-by: Martin Jäger <martin@libre.solar>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This mirrors #36499 and other PRs that added them for other
architectures.
This silences a large number of dtc warnings due to the missing
property. It seems reasonable to require an address-cells property since
any interrupt controller could be the parent of an interrupt-map.
The only device actually using interrupt-maps is neorv32, and it needs
an address-cells of 2 (since this is the default if none is specified it
worked like that before this change).
While I touched this, I reordered the properties for consistency across
boards, but there's a lot of variance here already.
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
In 8f9290d274 ('dts: bindings: riscv: Add and use bindings for
sifive CPUs'), new compat strings for SiFive CPUs were added, but with
riscv prefixes. Vendor-specific compats should just be prefixed with the
vendor, so move that over here.
Fixes: 8f9290d274 ('dts: bindings: riscv: Add and use bindings
for sifive CPUs')
Signed-off-by: Olof Johansson <olof@lixom.net>
The ns16550 flags reg-shift property as optional. In case it is not
supplied, the ns16550 driver relies on a value defined in <soc.h>, or,
by default it takes 4 (shift by 2).
This patch adds the property to all ns16550 nodes, with the following
values:
- 2 if SoC did not have any custom value defined by
UART_REG_ADDR_INTERVAL (corresponds to 1 << 2 = 4)
- If SoC defined DEFAULT_REG_INTERVAL (snps_arc_iot/it8xxx2), use such
value (4=2, 2=1, 1=0).
These changes will allow simplifying the ns16550 driver.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
To support both 8-bit and 32-bit Control/Status register variants, register
offsets need to be calculated from device tree.
Updated register data in device tree to the 32-bit CSR variant.
Renamed defines to be similar to other LiteX drivers.
Changed frequencies in clock-outputs nodes, so i2s/litex sample works.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Correct width when accessing LITEETH_RX_LENGTH register.
Also update register data in device tree to the 32-bit CSR variant.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Make driver take register info from device tree so it can work with both
8-bit and 32-bit CSRs.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
On Espressif SoCs, the pin controller is a virtual device.
Pin settings are actually controlled in a distributed way.
Therefore, that node does not belong to the SoC bus.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
e8e88dea incorrectly changed registers
used in `sys_clock_cycle_get(32|64)` functions.
This commit fixes that.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Kumar Gala