The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The ARM_MPU_NRF52X option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_NRF52X option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
When I2C and SPI are not used (such as when building a simple
bootloader for this target), the current Kconfig is generating a fair
bit of warning spew. Clean it up by moving some explicit _defconfig
settings into defaults.
Signed-off-by: Marti Bolivar <marti@foundries.io>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Johann Fischer